IT Exam Items Repository

Last Updated: Jun 24, 2026
IT Exam Items Repository › Category: CCNA
Which of the following routing protocols is considered to use link-state logic?
ITExamAnswers Editorial Team asked 4 years ago • 
A LAN design uses a Layer 3 EtherChannel between two switches SW1 and SW2, with port-channel interface 1 used on both switches. SW1 uses ports G0/1 and G0/2 in the channel. However, only interface G0/1 is bundled into the channel and working. Think about the configuration settings on port G0/2 that could have existed before adding G0/2 to the EtherChannel. Which answers identify a setting that could prevent IOS from adding G0/2 to the Layer 3 EtherChannel? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
A LAN design uses a Layer 3 EtherChannel between two switches SW1 and SW2, with port-channel interface 1 used on both switches. SW1 uses ports G0/1, G0/2, and G0/3 in the channel. Which of the following are true about SW1’s configuration to make the channel be able to route IPv4 packets correctly? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
An engineer has successfully configured a Layer 3 switch with SVIs for VLANs 2 and 3. Hosts in the subnets using VLANs 2 and 3 can ping each other with the Layer 3 switch routing the packets. The next week, the network engineer receives a call that those same users can no longer ping each other. If the problem is with the Layer 3 switching function, which of the following could have caused the problem? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
A Layer 3 switch has been configured to route IP packets between VLANs 1, 2, and 3 using SVIs, which connect to subnets 172.20.1.0/25, 172.20.2.0/25, and 172.20.3.0/25, respectively. The engineer issues a show ip route connected command on the Layer 3 switch, listing the connected routes. Which of the following answers lists a piece of information that should be in at least one of the routes?
ITExamAnswers Editorial Team asked 4 years ago • 
Router R1 has a router-on-a-stick (ROAS) configuration with two subinterfaces of interface G0/1: G0/1.1 and G0/1.2. Physical interface G0/1 is currently in a down/down state. The network engineer then configures a shutdown command when in interface configuration mode for G0/1.1 and a no shutdown command when in interface configuration mode for G0/1.2. Which answers are correct about the interface state for the subinterfaces? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
Router 1 has a Fast Ethernet interface 0/0 with IP address 10.1.1.1. The interface is connected to a switch. This connection is then migrated to use 802.1Q trunking. Which of the following commands could be part of a valid configuration for Router 1’s Fa0/0 interface? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
Router R1 lists a route in its routing table. Which of the following answers list a fact from a route that the router uses when matching the packet’s destination address? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
A router lists the following partial output from the show ip route command. Out which interface will the router route packets destined to IP address 10.1.15.122?
ITExamAnswers Editorial Team asked 4 years ago • 
A network engineer configures the ip route 10.1.1.0 255.255.255.0 s0/0/0 command on a router and then issues a show ip route command from enable mode. No routes for subnet 10.1.1.0/24 appear in the output. Which of the following could be true?
ITExamAnswers Editorial Team asked 4 years ago • 
Which of the following commands correctly configures a static route?
ITExamAnswers Editorial Team asked 4 years ago • 
An engineer configures a static IPv4 route on Router R1. Which of the following pieces of information should not be listed as a parameter in the configuration command that creates this static IPv4 route?
ITExamAnswers Editorial Team asked 4 years ago • 
After configuring a working router interface with IP address/mask 10.1.1.100/26, which of the following routes would you expect to see in the output of the show ip route command? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
Which of the following is different on the Cisco switch CLI for a Layer 2 switch as compared with the Cisco router CLI?
ITExamAnswers Editorial Team asked 4 years ago • 
Which of the following commands do not list the IP address and mask of at least one interface? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
« Previous1…113114115116117…207Next »
Ask Question

About The Author

ITExam Editorial Team

The ITExamAnswers Editorial Team is a dedicated group of certified IT professionals and network engineers. We rigorously review, verify, and update all exam materials to ensure you receive the most accurate and reliable resources for your certification journey.