IT Exam Items Repository

Last Updated: Jun 24, 2026
IT Exam Items Repository › Category: CCNA
A switch has just arrived from Cisco. The switch has never been configured with any VLANs, but VTP has been disabled. An engineer configures the vlan 22 and name Hannahs-VLAN commands and then exits configuration mode. Which of the following are true? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
Imagine that you are told that switch 1 is configured with the dynamic auto parameter for trunking on its Fa0/5 interface, which is connected to switch 2. You have to configure switch 2. Which of the following settings for trunking could allow trunking to work? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
Switch SW1 sends a frame to switch SW2 using 802.1Q trunking. Which of the answers describes how SW1 changes or adds to the Ethernet frame before forwarding the frame to SW2?
ITExamAnswers Editorial Team asked 4 years ago • 
Imagine a switch with three configured VLANs. How many IP subnets are required, assuming that all hosts in all VLANs want to use TCP/IP?
ITExamAnswers Editorial Team asked 4 years ago • 
In a LAN, which of the following terms best equates to the term VLAN?
ITExamAnswers Editorial Team asked 4 years ago • 
Switch SW1 connects via a cable to switch SW2’s G0/1 port. Which of the following conditions is the most likely to cause SW1’s late collision counter to continue to increment?
ITExamAnswers Editorial Team asked 4 years ago • 
Which of the following are true about the link after it comes up? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
The output of the show interfaces status command on a 2960 switch shows interface Fa0/1 in a “disabled” state. Which of the following is true about interface Fa0/1? (Choose three answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
A Cisco Catalyst switch connects with its Gigabit0/1 port to an end user’s PC. The end user, thinking the user is helping, manually sets the PC’s OS to use a speed of 1000 Mbps and to use full duplex, and disables the use of autonegotiation. The switch’s G0/1 port has default settings for speed and duplex. What speed and duplex settings will the switch decide to use? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
In which of the following modes of the CLI could you configure the duplex setting for interface Fast Ethernet 0/5?
ITExamAnswers Editorial Team asked 4 years ago • 
Which of the following describes a way to disable IEEE standard autonegotiation on a 10/100 port on a Cisco switch?
ITExamAnswers Editorial Team asked 4 years ago • 
Which of the following line subcommands tells a switch to wait until a show command’s output has completed before displaying log messages on the screen?
ITExamAnswers Editorial Team asked 4 years ago • 
A Layer 2 switch configuration places all its physical ports into VLAN 2. The IP addressing plan shows that address 172.16.2.250 (with mask 255.255.255.0) is reserved for use by this new LAN switch and that 172.16.2.254 is already configured on the router connected to that same VLAN. The switch needs to support SSH connections into the switch from any subnet in the network. Which of the following commands are part of the required configuration in this case? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
An engineer’s desktop PC connects to a switch at the main site. A router at the main site connects to each branch office through a serial link, with one small router and switch at each branch. Which of the following commands must be configured on the branch office switches, in the listed configuration mode, to allow the engineer to telnet to the branch office switches and supply only a password to login? (Choose three answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
An engineer had formerly configured a Cisco 2960 switch to allow Telnet access so that the switch expected a password of mypassword from the Telnet user. The engineer then changed the configuration to support Secure Shell. Which of the following commands could have been part of the new configuration? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
« Previous1…117118119120121…207Next »
Ask Question

About The Author

ITExam Editorial Team

The ITExamAnswers Editorial Team is a dedicated group of certified IT professionals and network engineers. We rigorously review, verify, and update all exam materials to ensure you receive the most accurate and reliable resources for your certification journey.