IT Exam Items Repository

Last Updated: Jun 24, 2026
IT Exam Items Repository › Category: CCNP
OSPFv3 has three LSA flooding scope types. In addition to area scope what are the other two flooding scopes? (Choose two.)
ITExamAnswers Editorial Team asked 5 years ago • 
Which global configuration command will start OSPFv3 address families routing on a Cisco router?
ITExamAnswers Editorial Team asked 5 years ago • 
The LS Type field in OSPFv3 LSAs has been increased from 8 bits to 16 bits. What is a purpose of two of the high-order bits in this extended field?
ITExamAnswers Editorial Team asked 5 years ago • 
What is the result of a router being configured with OSPFv3 for IPv6 when no explicit RID is configured and there are no active IPv4 interfaces?
ITExamAnswers Editorial Team asked 5 years ago • 
When configuring OSPFv3 summarization, on which router should summarization be configured?
ITExamAnswers Editorial Team asked 6 years ago • 
Which two OSPFv3 LSA types are used to advertise IPv6 unicast address prefixes and prevent the need for SPF calculations every time an address prefix is added or changed on a router interface? (Choose two.)
ITExamAnswers Editorial Team asked 5 years ago • 
Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco routers as shown. PC1 is unable to connect to PC2. What should the administrator do first when troubleshooting the OSPFv2 implementation?
ITExamAnswers Editorial Team asked 7 years ago • 
Refer to the exhibit. A network administrator issued the command show ip ospf interface on the router R2. What conclusion can be drawn?
ITExamAnswers Editorial Team asked 6 years ago • 
In an OSPF hub-and-spoke topology, what needs to be done, if anything, to ensure that the spoke routers would never be selected as DR and BDR?
ITExamAnswers Editorial Team asked 5 years ago • 
A network engineer has noted that some expected network route entries are not displayed in the routing table. Which two commands will provide additional information about the state of router adjacencies, timer intervals, and the area ID? (Choose two.)
ITExam Editorial Team asked 6 years ago • 
Refer to the exhibit. LTC has an OSPF neighbor relationship with the router LTA over the 203.0.113.12/30 network. The 203.0.113.16/30 network link should serve as a backup when the OSPF link goes down. The floating static route command ip route 0.0.0.0 0.0.0.0 S0/1/1 100 was issued on LTC and now traffic is using the backup link even when the OSPF link is up and functioning. Which change should be made to the static route command so that traffic will only use the OSPF link when it is up
ITExamAnswers Editorial Team asked 5 years ago • 
A network engineer is tracing packets through the network but packets are not load balancing over paths as expected. What are two actions the engineer should take? (Choose two.)
ITExamAnswers Editorial Team asked 5 years ago • 
Which command should be used to check the OSPF process ID, the router ID, networks the router is advertising, the neighbors the router is receiving updates from, and the default administrative distance?
ITExamAnswers Editorial Team asked 6 years ago • 
Which destination address is used by EIGRP for IPv6 messages?
ITExamAnswers Editorial Team asked 5 years ago • 
Refer to the exhibit. A network administrator configures AAA authentication on router R1. The ACS servers are configured and running. The administrator tests the configuration by telneting to R1. What will happen if the administrator attempts to authenticate through the RADIUS server using incorrect credentials?
ITExam Editorial Team asked 5 years ago • ,
« Previous1…7475767778…133Next »
Ask Question

About The Author

ITExam Editorial Team

The ITExamAnswers Editorial Team is a dedicated group of certified IT professionals and network engineers. We rigorously review, verify, and update all exam materials to ensure you receive the most accurate and reliable resources for your certification journey.