IT Exam Items Repository

Last Updated: Jun 24, 2026
IT Exam Items Repository › Category: CCNP
Refer to the exhibit. A network administrator issues the show run | section username|aaa|line|radius command to verify an AAA configuration on a Cisco router. Which two conclusions can be drawn from the command output? (Choose two.)
ITExam Editorial Team asked 6 years ago • 
Refer to the exhibit. The total number of packet flows is not consistent with what is expected by the network administrator. The results show only half of the flows that are typically captured for the interface. Pings between the router and the collector are successful. What is the reason for the unexpected results?
ITExamAnswers Editorial Team asked 6 years ago • 
Refer to the exhibit. A network administrator issues the command show bgp ipv6 unicast | begin Network to check the BGP table. Which statement describes the routes with an unspecified address (::) in the Next Hop column?
ITExamAnswers Editorial Team asked 6 years ago • 
When an unlabeled packet arrives at an MPLS-enabled router interface, which database is used to make a forwarding decision on the packet?
ITExam Editorial Team asked 6 years ago • 
Match the MPLS router type to its characteristic.
ITExam Editorial Team asked 6 years ago • 
Refer to the exhibit. A network administrator configured a class map as shown, but the traffic is not being classified as desired. Which conclusion can be drawn from this configuration?
ITExam Editorial Team asked 6 years ago • 
Refer to the exhibit. An administrator wants EIGRP on Router1 to load balance traffic to network 2001:db8:11:10::/64 across two interfaces. Currently traffic is using only interface GigabitEthernet0/1. A second route, not in the routing table, is available with a metric of 264000. What value is needed in the variance command to make EIGRP put the second route into the routing table?
ITExamAnswers Editorial Team asked 6 years ago • ,
Refer to the exhibit. Routers R1 and R2 enable EIGRP on all of their interfaces. Which two conclusions can the field engineer draw from the outputs of the show ip route eigrp command on each router? (Choose two.)
ITExam Editorial Team asked 6 years ago • 
Refer to the exhibit. An administrator has entered the command default-information originate in OSPFv3 global configuration mode on R1, but R2 is not receiving a default route. What is the problem?
ITExam Editorial Team asked 6 years ago • 
Refer to the exhibit. Routers R1 and R2 are configured as shown. However, the show ipv6 ospf neighbor command reveals that there are no OSPFv3 neighbors established. What error in the configuration is preventing neighbor relationship from forming between the two routers?
ITExamAnswers Editorial Team asked 6 years ago • 
Refer to the exhibit. A network administrator has configured two-way redistribution on router R1. However, OSPF routes are not being redistributed into the EIGRP domain. What is causing this issue?
ITExam Editorial Team asked 6 years ago • 
What OSPF LSA type is used to advertise routes redistributed into an OSPF domain?
ITExam Editorial Team asked 6 years ago • 
Match the IPsec function with its description. (Not all options are used.)
ITExam Editorial Team asked 6 years ago • 
Refer to the exhibit. Considering that R2, R3, and R4 are correctly configured, why did R1 not establish an adjacency with R2, R3, and R4?
ITExamAnswers Editorial Team asked 6 years ago • ,
A network administrator is writing a standard ACL that will deny any traffic from the 172.16.0.0/16 network, but permit all other traffic. Which two commands should be used? (Choose two.)
ITExamAnswers Editorial Team asked 7 years ago • ,
« Previous1…7576777879…133Next »

About The Author

ITExam Editorial Team

The ITExamAnswers Editorial Team is a dedicated group of certified IT professionals and network engineers. We rigorously review, verify, and update all exam materials to ensure you receive the most accurate and reliable resources for your certification journey.