IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it IT Questions Bank › Category: CCNAA switch has just arrived from Cisco. The switch has never been configured with any VLANs, but VTP has been disabled. An engineer configures the vlan 22 and name Hannahs-VLAN commands and then exits configuration mode. Which of the following are true? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNAImagine that you are told that switch 1 is configured with the dynamic auto parameter for trunking on its Fa0/5 interface, which is connected to switch 2. You have to configure switch 2. Which of the following settings for trunking could allow trunking to work? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNASwitch SW1 sends a frame to switch SW2 using 802.1Q trunking. Which of the answers describes how SW1 changes or adds to the Ethernet frame before forwarding the frame to SW2?ITExamAnswers asked 2 years ago • CCNAImagine a switch with three configured VLANs. How many IP subnets are required, assuming that all hosts in all VLANs want to use TCP/IP?ITExamAnswers asked 2 years ago • CCNAIn a LAN, which of the following terms best equates to the term VLAN?ITExamAnswers asked 2 years ago • CCNASwitch SW1 connects via a cable to switch SW2’s G0/1 port. Which of the following conditions is the most likely to cause SW1’s late collision counter to continue to increment?ITExamAnswers asked 2 years ago • CCNAWhich of the following are true about the link after it comes up? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNAThe output of the show interfaces status command on a 2960 switch shows interface Fa0/1 in a “disabled” state. Which of the following is true about interface Fa0/1? (Choose three answers.)ITExamAnswers asked 2 years ago • CCNAA Cisco Catalyst switch connects with its Gigabit0/1 port to an end user’s PC. The end user, thinking the user is helping, manually sets the PC’s OS to use a speed of 1000 Mbps and to use full duplex, and disables the use of autonegotiation. The switch’s G0/1 port has default settings for speed and duplex. What speed and duplex settings will the switch decide to use? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNAIn which of the following modes of the CLI could you configure the duplex setting for interface Fast Ethernet 0/5?ITExamAnswers asked 2 years ago • CCNAWhich of the following describes a way to disable IEEE standard autonegotiation on a 10/100 port on a Cisco switch?ITExamAnswers asked 2 years ago • CCNAWhich of the following line subcommands tells a switch to wait until a show command’s output has completed before displaying log messages on the screen?ITExamAnswers asked 2 years ago • CCNAA Layer 2 switch configuration places all its physical ports into VLAN 2. The IP addressing plan shows that address 172.16.2.250 (with mask 255.255.255.0) is reserved for use by this new LAN switch and that 172.16.2.254 is already configured on the router connected to that same VLAN. The switch needs to support SSH connections into the switch from any subnet in the network. Which of the following commands are part of the required configuration in this case? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNAAn engineer’s desktop PC connects to a switch at the main site. A router at the main site connects to each branch office through a serial link, with one small router and switch at each branch. Which of the following commands must be configured on the branch office switches, in the listed configuration mode, to allow the engineer to telnet to the branch office switches and supply only a password to login? (Choose three answers.)ITExamAnswers asked 2 years ago • CCNAAn engineer had formerly configured a Cisco 2960 switch to allow Telnet access so that the switch expected a password of mypassword from the Telnet user. The engineer then changed the configuration to support Secure Shell. Which of the following commands could have been part of the new configuration? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNA