IT Questions Bank

Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments
Tweet Share Pin it

IT Questions Bank 1

IT Questions Bank › Category: CCNP 300-410
R1 and R2 are configured as eBGP neighbor , R1 is in AS100 and R2 is in AS200. R2 is advertising these networks to R1: The network administrator on R1 must improve convergence by blocking all subnets of 172.16.0.0/16 major network with a mask lower than 23 from coming in, Which set of configurations accomplishes the task on R1?
IT Questions Bank 2IT Administrator asked 2 years ago • 
Refer to the exhibit. The AP status from Cisco DNA Center Assurance Dashboard shows some physical connectivity issues from access switch interface G1/0/14. Which command generates the diagnostic data to resolve the physical connectivity issues?
IT Questions Bank 2IT Administrator asked 2 years ago • 
Refer to the exhibit. An engineer configures the router 10.1.100.10 for EIGRP autosummarization so that R1 should receive the summary route of 10.0.0.0/8. However, R1 receives more specific /24 routes. Which action resolves this issue?
IT Questions Bank 2IT Administrator asked 2 years ago • 
Refer to the exhibit. Although summarization is configured for R1 to receive 10.0.0.0/8. more specific routes are received by R1. How should the 10.0.0.0/8 summary route be received from the neighbor, attached to R1 via Fast Ethernet0/0 interface?
IT Questions Bank 2IT Administrator asked 2 years ago • 
Refer to the exhibit. R1 is configured with IP SLA to check the availability of the server behind R6 but it kept failing. Which configuration resolves the issue?
IT Questions Bank 2IT Administrator asked 2 years ago • 
Which 0S1 model is used to insert an MPLS label?
IT Questions Bank 2IT Administrator asked 2 years ago • 
The network administrator configured R1 to authenticate Telnet connections based on Cisco ISE using TACACS+. ISE has been configured with an IP address of 192.168.1.5 and with a network device pointing toward R1(192.168.1.1) with a shared secret password of Cisco123.
IT Questions Bank 2IT Administrator asked 2 years ago • 
Refer to the exhibit. After a security audit, the administrator implemented an ACL in the route reflector. The RR became unreachable from any router in the network. Which two actions resolve the issue? (Choose two.)
IT Questions Bank 2IT Administrator asked 2 years ago • 
A company is expanding business by opening 35 branches over the Internet. A network engineer must configure DMVPN at the branch routers to connect with the hub router and allow NHRP to add spoke routers securely to the multicast NHRP mappings automatically Which configuration meets this requirement at the hub router?
IT Questions Bank 2IT Administrator asked 2 years ago • 
What is a function of IPv6 Source Guard?
IT Questions Bank 2IT Administrator asked 2 years ago • 
Refer to the exhibit. An engineer must block access to the console ports for all corporate remote Cisco devices based on the recent corporate security policy but the security team stilt can connect through the console port. Which configuration on the console port resolves the issue?
IT Questions Bank 2IT Administrator asked 2 years ago • 
Refer to the exhibit. A junior engineer configured SNMP to network devices. Malicious users have uploaded different configurations to the network devices using SNMP and TFTP servers. Which configuration prevents changes from unauthorized NMS and TFTP servers?
IT Questions Bank 2IT Administrator asked 2 years ago • 
Refer to the exhibit. An engineer has configured R1 as EIGRP stub router. After the configuration, router R3 failed to reach to R2 loopback address. Which action advertises R2 loopback back into the R3 routing table?
IT Questions Bank 2IT Administrator asked 2 years ago • 
Refer to the exhibit. The network administrator configured the network to connect two disjointed networks and ail the connectivity is up except the virtual link which causes area 250 to be unreachable. Which two configurations resolve this issue? (Choose two.)
IT Questions Bank 2IT Administrator asked 2 years ago • 
Refer to the exhibit. The DHCP client is unable to receive an IP address from the DHCP server RouterB is configured as follows: Which command is required on the fastethernet 0/0 interface of RouterB to resolve this issue?
IT Questions Bank 2IT Administrator asked 2 years ago • 
« Previous123456Next »
Ask Question