IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it IT Questions Bank › Category: CCNP ROUTEWhat are two reasons for creating an OSPF network with multiple areas? (Choose two.)ITExamAnswers asked 4 years ago • CCNA, CCNP, CCNP ROUTE, CCNP ROUTE v6.0A network administrator is implementing OSPF in a portion of the network and must ensure that only specific routes are advertised via OSPF. Which network statement would configure the OSPF process for networks 192.168.4.0, 192.168.5.0, 192.168.6.0, and 192.168.7.0, now located in the backbone area, and inject them into the OSPF domain?ITExamAnswers asked 4 years ago • CCNA, CCNP, CCNP ROUTE, CCNP ROUTE v6.0In an OSPF hubandspoke topology, what needs to be done to ensure that the spoke routers would never be selected as DR and BDR?ITExamAnswers asked 1 year ago • CCNP ROUTE, CCNP ROUTE v6.0Refer to the exhibit. All three routers are exchanging EIGRP routes. What value represents the advertised distance of the feasible successor for the 10.1.2.0/24 network?ITExamAnswers asked 1 year ago • CCNP ROUTE, CCNP ROUTE v6.0Refer to the exhibit. Based on the output of show ip eigrp neighbors, what are two possible problems with adjacencies between Router1 and Router2? (Choose two.)ITExamAnswers asked 2 years ago • CCNA 2 v4, CCNP ROUTE, CCNP ROUTE v6.0When does an EIGRP router place a route in the active state?ITExamAnswers asked 1 year ago • CCNP ROUTE, CCNP ROUTE v6.0Which two solutions are used in an EIGRP network to reduce DUAL computations? (Choose two.)ITExamAnswers asked 1 year ago • CCNP ROUTE, CCNP ROUTE v6.0The network administrator wants RTA to send only the summarized route of 10.10.0.0/16 to RTB. Which configuration will accomplish this?ITExamAnswers asked 1 year ago • CCNP ROUTE, CCNP ROUTE v6.0Which statement is a requirement for the EIGRP AS number?ITExamAnswers asked 1 year ago • CCNP ROUTE, CCNP ROUTE v6.0Which EIGRP algorithm tracks all the routes that are advertised by neighbors and uses the composite metric of each route to compare the routes?ITExamAnswers asked 1 year ago • CCNP ROUTE, CCNP ROUTE v6.0Refer to the exhibit. All routers are configured for OSPF area 0. The network administrator requires that R2 always be the DR and maintain adjacency. Which two configurations can achieve this? (Choose two.)ITExamAnswers asked 1 year ago • CCNA 2 v4, CCNP ROUTERefer to the exhibit. A GRE tunnel must be configured between routers RTA and RTB. Assume that router RTB has been correctly configured. Which set of commands would correctly configure router RTA to encrypt traffic destined for router RTB?ITExamAnswers asked 1 year ago • CCNP ROUTERefer to the exhibit. R1 and R2 are unable to establish a BGP peer relationship. After a network administrator has confirmed that each router can ping the loopback interface of the other router, what can be done to fix this problem?ITExamAnswers asked 1 year ago • CCNP ROUTERefer to the diagram and configuration. OSPF is configured over Frame Relay using neighbor statements under router ospf mode. Although all PVCs are active, RTB and RTC do not see all OSPF routes in their routing tables. What could be done to fix this problem? (Choose two.)ITExamAnswers asked 1 year ago • CCNP ROUTERefer to the exhibit. After configuring the IPv6 manual tunnel, a network administrator tries to verify the configuration from R1. Which IP addresses should be included in the extended ping command in order to verify the status of the tunnel?ITExamAnswers asked 1 year ago • CCNP ROUTE