IT Questions Bank

March 16, 2020 Last Updated: June 13, 2021 No Comments
Tweet Share Pin it

IT Questions Bank 1

IT Questions Bank › Category: CCNP
Filter:AllUnanswered
What happens when an edge router using IntServ QoS determines that the data pathway cannot support the level of QoS requested?
IT Questions Bank 2IT Administrator asked 9 months ago • ,
239 views0 answers0 votes
Which QoS model is very resource intensive and provides the highest guarantee of QoS?
IT Questions Bank 3ITExamAnswers asked 1 year ago • ,
211 views0 answers0 votes
What happens when the memory queue of a device fills up and new network traffic is received?
IT Questions Bank 3ITExamAnswers asked 9 months ago • ,
166 views0 answers0 votes
What role do network devices play in the IntServ QoS model?
IT Questions Bank 3ITExamAnswers asked 2 years ago • ,
272 views0 answers0 votes
When dynamic NAT without overloading is being used, what happens if seven users attempt to access a public server on the Internet when only six addresses are available in the NAT pool?
IT Questions Bank 3ITExamAnswers asked 1 year ago • ,
425 views0 answers0 votes
A company designs its network so that the PCs in the internal network are assigned IP addresses from DHCP servers, and the packets that are sent to the Internet are translated through a NAT-enabled router. What type of NAT enables the router to populate the translation table from a pool of unique public addresses, as the PCs send packets through the router to the Internet?
IT Questions Bank 3ITExamAnswers asked 9 months ago • ,
247 views0 answers0 votes
Why is NAT not needed in IPv6?​
IT Questions Bank 3ITExamAnswers asked 2 years ago • ,
1643 views0 answers0 votes
A network administrator wants to examine the active NAT translations on a border router. Which command would perform the task?
IT Questions Bank 3ITExamAnswers asked 2 years ago • ,
345 views0 answers0 votes
An administrator has configured an access list on R1 to allow SSH administrative access from host 172.16.1.100. Which command correctly applies the ACL?
IT Questions Bank 3ITExamAnswers asked 1 year ago • ,
838 views0 answers0 votes
Which three statements describe ACL processing of packets? (Choose three.)
IT Questions Bank 3ITExamAnswers asked 1 year ago • , ,
694 views0 answers0 votes
A network administrator configures an ACL with the command R1(config)# access-list 1 permit 172.16.0.0 0.0.15.255. Which two IP addresses will match this ACL statement? (Choose two.)
IT Questions Bank 3ITExamAnswers asked 9 months ago • , ,
286 views0 answers0 votes
A network administrator has just changed the router ID on a router that is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use the new router ID?
IT Questions Bank 3ITExamAnswers asked 1 year ago • ,
302 views0 answers0 votes
Which command, if applied on an OSPF router, would give a Gigabit Ethernet interface a lower cost than a Fast Ethernet interface?
IT Questions Bank 2IT Administrator asked 5 months ago • ,
59 views0 answers0 votes
A router with two LAN interfaces, two WAN interfaces, and one configured loopback interface is operating with OSPF as its routing protocol. What does the router OSPF process use to assign the router ID?
IT Questions Bank 3ITExamAnswers asked 1 year ago • 
316 views0 answers0 votes
The OSPF hello timer has been set to 15 seconds on a router in a point-to-point network. By default, what is the dead interval on this router?
IT Questions Bank 2IT Administrator asked 6 months ago • ,
138 views0 answers0 votes
123…147Next »
Ask Question


Related Articles