After you configure the Loopback0 interface, Which command can you enter to verify the status of the interface and determine whether fast switching is enabled?

Question:
After you configure the Loopback0 interface, Which command can you enter to verify the status of the interface and determine whether fast switching is enabled?

• Router#show ip interface loopback 0
• Router#show run
• Router#show interface loopback 0
• Router#show ip interface brief

Explanation: Output from real device

Router2901#sh int g0/0
GigabitEthernet0/0 is up, line protocol is up
Hardware is CN Gigabit Ethernet, address is c471.fe99.9999 (bia c471.fe99.9999)
Description: Lan
Internet address is 10.1.1.1/25
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1Gbps, media type is RJ45
output flow-control is unsupported, input flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of “show interface” counters never
Input queue: 0/75/61/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 39000 bits/sec, 30 packets/sec
5 minute output rate 73000 bits/sec, 37 packets/sec
41068530 packets input, 3905407112 bytes, 0 no buffer
Received 8678853 broadcasts (0 IP multicasts)
0 runts, 0 giants, 45 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 79853 multicast, 0 pause input
39267208 packets output, 2262399504 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
79926 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
Router2901#
Router2901 ip int g0/0
GigabitEthernet0/0 is up, line protocol is up
Internet address is 10.1.1.1/25
Broadcast address is 255.255.255.255
Address determined by non-volatile memory
MTU is 1500 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Secondary address 192.168.1.7/24
Multicast reserved groups joined: 224.0.0.10
Outgoing access list is not set
Inbound access list is not set
Proxy ARP is enabled
Local Proxy ARP is disabled
Security level is default
Split horizon is enabled
ICMP redirects are always sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is enabled
IP fast switching on the same interface is disabled
IP Flow switching is disabled
IP CEF switching is enabled
IP CEF switching turbo vector
IP multicast fast switching is enabled
IP multicast distributed fast switching is disabled
IP route-cache flags are Fast, CEF
Router Discovery is disabled
IP output packet accounting is disabled
IP access violation accounting is disabled
TCP/IP header compression is disabled
RTP/IP header compression is disabled
Policy routing is disabled
Network address translation is enabled, interface in domain inside
BGP Policy Mapping is disabled
Input features: Common Flow Table, Stateful Inspection, Virtual Fragment Reassembly, Virtual Fragment Reassembly After IPSec Decryption, CAR, MCI Check
Output features: NAT Inside, Common Flow Table, Stateful Inspection, NAT ALG proxy, CAR
Post encapsulation features: CAR
IPv4 WCCP Redirect outbound is disabled
IPv4 WCCP Redirect inbound is disabled
IPv4 WCCP Redirect exclude is disabled
Router2901#

Exam with this question: CCNA v3.0 (200-125) Study Guide – Exam Dumps