IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it Which statement describes the use of a network baseline?ITExamAnswers asked 9 months ago • CCNA Discovery v4Refer to the exhibit. The routers are configured with RIPv2 and utilize the default configuration. When attempting to communicate with other networks, hosts from 172.31.1.0/24 are experiencing connectivity issues. What could be done to resolve this issue?ITExamAnswers asked 9 months ago • CCNA Discovery v4A network administrator has configured Frame Relay on a serial interface and issued the show interfaces serial command. The output shows that the interface is up and the line protocol is up. However, pings to the remote router across the link fail. What should the next step be to ensure that the IP address of the remote router appears in the Frame Relay map table of the local router?ITExamAnswers asked 9 months ago • CCNA Discovery v4A network designer has chosen to specify the use of a dedicated firewall appliance at the perimeter of a large network. Why would the designer use a dedicated firewall rather than using the Cisco IOS firewall feature set on the existing router?ITExamAnswers asked 9 months ago • CCNA Discovery v4Which security procedure should be considered to protect a server farm against internal attacks?ITExamAnswers asked 9 months ago • CCNA Discovery v4What is a signaling standard that is used for managing and maintaining the connection between a CPE router and the service provider Frame Relay switch?ITExamAnswers asked 9 months ago • CCNA Discovery v4A network administrator is integrating IPv6 into an IPv4 network by encapsulating one protocol packet within another protocol. Which transition method is being used?ITExamAnswers asked 9 months ago • CCNA Discovery v4A network administrator is asked to upgrade the enterprise network devices and to modify the addressing scheme to support VLSM and route summarization. The current network infrastructure contains both Cisco and non-Cisco routers. The plan is to replace old routers gradually with the latest Cisco routers. Which two routing protocols can the administrator use to support both upgrading requirements? (Choose two.)ITExamAnswers asked 9 months ago • CCNA Discovery v4Refer to the exhibit. A network engineer applies the ACL that is shown in the exhibit to interface S0/0/0 on router R1 outbound. What impact will the ACL have on traffic that moves through interface S0/0/0?ITExamAnswers asked 9 months ago • CCNA Discovery v4Refer to the exhibit. EIGRP has been configured as a routing protocol in the network. Users who are connected on LAN_1 and LAN_2 can ping their default gateways. Users on LAN_1 complain that they are unable to access the resources on the file server that is connected to LAN_2. A technician issues the show ip interface brief command on R1 to verify the status of the interfaces. What information will help the technician troubleshoot the issue?ITExamAnswers asked 9 months ago • CCNA Discovery v4In a converged network, which two types of traffic would be categorized as real-time traffic? (Choose two.)ITExamAnswers asked 1 year ago • CCNA Discovery v4, CCNP ROUTE v6.0What are the primary design goals for the core Layer?ITExamAnswers asked 9 months ago • CCNA Discovery v4Refer to the exhibit. A NetworkingCompany engineer is characterizing an existing network for a new customer. The engineer issues a show running-config command on the branch router to gather configuration information. What is the engineer able to determine as a result of viewing the output of this command?ITExamAnswers asked 9 months ago • CCNA Discovery v4Refer to the exhibit. A networking company designer is reviewing a diagram of a customer network. What are the two problems that need to be resolved in the topology that is shown? (Choose two.)ITExamAnswers asked 9 months ago • CCNA Discovery v4A WIC-1T module needs to be installed in a Cisco 1841 router that currently has a WIC-2T module in slot 0. What should the network technician do first?ITExamAnswers asked 9 months ago • CCNA Discovery v4