IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it IT Questions Bank › Category: CCNPWhich network prefix matches the prefix match pattern 10.0.0.0/8 ge 16 le 24?ITExamAnswers asked 3 years ago • CCNPWhat is the only attribute used by standard access control lists to identify traffic?ITExamAnswers asked 4 years ago • CCNA CyberOps, CCNPRefer to the exhibit. A network administrator issues the show bgp ipv4 unicast | begin Network command on router R5 to verify routes in the BGP table. The administrator realizes that the route 10.1.1.0/24 and the component subnets learned from router R1 with IP address of 1.1.1.1 will not be installed in the routing table. What is a possible solution to the issue?ITExamAnswers asked 3 years ago • CCNPA network administrator is troubleshooting a BGP network where some BGP routes are missing from BGP tables. The administrator has verified that BGP peers were formed as expected. What are two possible reasons that routes would not appear in the BGP table or the routing table? (Choose two.)ITExamAnswers asked 3 years ago • CCNPRefer to the exhibit. A network administrator issues the show bgp ipv6 unicast | begin Network command on router R1 to verify routes in the IPv6 BGP table. Which statement describes the status of the route 2001:DB8:2::/64?ITExamAnswers asked 3 years ago • CCNPA network administrator receives a call, from a colleague at the overseas branch office, that a BGP route advertised by the company carries an autonomous number of 64520 in the AS_Path attribute. Which statement describes the situation?ITExamAnswers asked 3 years ago • CCNPRefer to the exhibit. A network administrator issues the show bgp ipv4 unicast command to check the routes in the BGP table. What does the indication of 0.0.0.0 under Next Hop mean?IT Administrator asked 3 years ago • CCNPA network technician is verifying the BGP configuration and neighbor relationships on a Cisco router. The technician suspects that one BGP neighbor lost the peering relationship. Which command should the technician use to verify the network link status?ITExamAnswers asked 3 years ago • CCNPA network administrator is troubleshooting a BGP network and issues the show bgp ipv4 unicast command on a BGP router. What is a purpose of using this command?ITExamAnswers asked 3 years ago • CCNPRefer to the exhibit. A network administrator is troubleshooting a BGP adjacency issue between routers R2 and R5. R2 uses loopback0 interface 2.2.2.2 and R5 uses loopback0 interface 5.5.5.5 in the neighbor ip_address remote-as as_number statement in their respective configurations. However, an adjacency does not form. Which two conclusions can be drawn from the troubleshooting process performed on R5? (Choose two.)ITExamAnswers asked 3 years ago • CCNPWhich statement describes the BGP evaluation criteria of path attributes during the calculation of the best path for a route?ITExamAnswers asked 3 years ago • CCNPRefer to the exhibit. A network administrator issues the show bgp ipv4 unicast 10.1.1.0 command on router R1 to verify that the network 10.1.1.0 is in the BGP table. The administrator notices that there are two routes to reach the network. Which BGP path attribute is used to determine the best-path?ITExamAnswers asked 3 years ago • CCNPA network administrator issues the show bgp ipv4 unicast summary command on a router to check the adjacency state with a neighbor router. The value under the State/PfxRcd field shows 0. Which statement describes the status of adjacency between the two routers?ITExamAnswers asked 3 years ago • CCNPWhat are two issues that may cause the failure of a BGP neighbor relationship from forming? (Choose two.)ITExamAnswers asked 3 years ago • CCNPRefer to the exhibit. A network administrator is configuring a BGP router. Which two statements describe the result of the configuration? (Choose two.)ITExamAnswers asked 3 years ago • CCNP