IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it IT Questions Bank › Category: CCNA 2 v6What are two advantages of static routing over dynamic routing? (Choose two.)ITExamAnswers asked 4 years ago • CCNA 2 v4.0 ERouting, CCNA 2 v6, CCNA 2 v7What two tasks do dynamic routing protocols perform? (Choose two.)ITExamAnswers asked 4 years ago • CCNA, CCNA 2 v4.0 ERouting, CCNA 2 v6, CCNA 3 v6What type of route allows a router to forward packets even though its routing table contains no specific route to the destination network?ITExamAnswers asked 4 years ago • CCNA, CCNA 2 v6, CCNA 2 v7, CCNA Discovery v4Which type of address does a switch use to build the MAC address table?ITExamAnswers asked 4 years ago • CCNA, CCNA 2 v6, CCNA 3 v7, Networking Basics, Networking EssentialsA network administrator configures the port security feature on a switch. The security policy specifies that each access port should allow up to two MAC addresses. When the maximum number of MAC addresses is reached, a frame with the unknown source MAC address is dropped and a notification is sent to the syslog server. Which security violation mode should be configured for each access port?ITExamAnswers asked 4 years ago • CCNA 2 v6Which two statements are true about NTP servers in an enterprise network? (Choose two.)ITExamAnswers asked 4 years ago • CCNA 2 v6, CCNA 3 v7, CCNA CyberOps, CCNP, DevNet, Endpoint SecurityThe network administrator configures the router with the ip route 172.16.1.0 255.255.255.0 172.16.2.2 command. How will this route appear in the routing table?ITExamAnswers asked 4 years ago • CCNA, CCNA 2 v4, CCNA 2 v6, CCNA 2 v7, CCNPWhat are two functions of a router? (Choose two.)ITExamAnswers asked 4 years ago • CCNA, CCNA 2 v4, CCNA 2 v6, CCNA 3 v6, CCNA 3 v7, Networking Basics, Networking EssentialsWhich two statements are true regarding classless routing protocols? (Choose two.)ITExamAnswers asked 4 years ago • CCNA, CCNA 2 v4, CCNA 2 v6What is one difference between using Telnet or SSH to connect to a network device for management purposes?ITExamAnswers asked 4 years ago • CCNA, CCNA 2 v6, CCNA 2 v7, CCNA Security, Networking Devices and Initial Configuration, Networking EssentialsWhich DHCPv4 message will a client send to accept an IPv4 address that is offered by a DHCP server?ITExamAnswers asked 4 years ago • CCNA 2 v6, CCNA 2 v7, Networking Basics, Networking Devices and Initial Configuration, Networking EssentialsA company uses the SLAAC method to configure IPv6 addresses for the employee workstations. Which address will a client use as its default gateway?ITExamAnswers asked 2 years ago • CCNA 2 v6, CCNA 2 v7, Network Addressing and Basic TroubleshootingWhich statement describes a difference between the operation of inbound and outbound ACLs?ITExamAnswers asked 4 years ago • CCNA 2 v6, CCNA 4 v6Which three statements are generally considered to be best practices in the placement of ACLs? (Choose three.)ITExamAnswers asked 4 years ago • CCNA, CCNA 2 v6, CCNA 4 v6, CCNA SecurityA network administrator needs to configure a standard ACL so that only the workstation of the administrator with the IP address 192.168.15.23 can access the virtual terminal of the main router. Which two configuration commands can achieve the task? (Choose two.)ITExamAnswers asked 4 years ago • CCNA, CCNA 2 v6, CCNA 4 v6, CCNA Security