IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it IT Questions Bank › Category: CCNA 3 v4Which two statements concerning network security are accurate? (Choose two.)ITExamAnswers asked 2 years ago • CCNA 3 v4Refer to the exhibit. All devices are configured as shown in the exhibit. PC2 can successfully ping the F0/0 interface on R1. PC2 cannot ping PC1. What might be the reason for this failure?ITExamAnswers asked 2 years ago • CCNA 3 v4Which two statements are true about the interface fa0/0.10 command? (Choose two.)ITExamAnswers asked 2 years ago • CCNA 3 v4Refer to the exhibit. The network administrator correctly configures RTA to perform inter-VLAN routing. The administrator connects RTA to port 0/4 on SW2, but inter-VLAN routing does not work. What could be the possible cause of the problem with the SW2 configuration?ITExamAnswers asked 2 years ago • CCNA 3 v4Which three elements must be used when configuring a router interface for VLAN trunking? (Choose three.)ITExamAnswers asked 2 years ago • CCNA 3 v4What distinguishes traditional routing from router-on-a-stick?ITExamAnswers asked 2 years ago • CCNA 3 v4Refer to the exhibit. Port Fa0/0 on router R1 is connected to port Fa0/1 on switch S1. After the commands shown are entered on both devices, thenetwork administrator determines that the devices on VLAN 2 are unable to ping the devices on VLAN 1. What is the likely problem?ITExamAnswers asked 2 years ago • CCNA 3 v4Devices on the network are connected to a 24-port Layer 2 switch that is configured with VLANs. Switch ports 0/2 to 0/4 are assigned to VLAN 10. Ports 0/5 to 0/8 are assigned to VLAN 20, and ports 0/9 to 0/12 are assigned to VLAN 30. All other ports are assigned to the default VLAN. Which solution allows all VLANs to communicate between each other while minimizing the number of ports necessary to connect the VLANs?ITExamAnswers asked 2 years ago • CCNA 3 v4Refer to the exhibit. Which three statements describe the network designshown in the exhibit? (Choose three.)ITExamAnswers asked 2 years ago • CCNA 3 v4Refer to the exhibit. What two conclusions can be drawn from the output that is shown? (Choose two.)ITExamAnswers asked 2 years ago • CCNA 3 v4Refer to the exhibit. PC1 has attempted to ping PC2 but has been unsuccessful. What could account for this failure?ITExamAnswers asked 2 years ago • CCNA 3 v4Refer to the exhibit. The commands for a router to connect to a trunked uplink are shown in the exhibit. A packet is received from IP address 192.168.1.54. The packet destination address is 192.168.1.120. What will the router do with this packet?ITExamAnswers asked 2 years ago • CCNA 3 v4Refer to the exhibit. Which two statements are true about the operation of the subinterfaces? (Choose two.)ITExamAnswers asked 2 years ago • CCNA 3 v4Refer to the exhibit. Switch1 is correctly configured for the VLANs that are displayed in the graphic. The configuration that is shown was applied to RTA to allow for interVLAN connectivity between hosts attached to Switch1. After testing the network, the administrator logged the following report: Why are hosts connected to Fa0/1 through Fa0/5 unable to communicate with hosts in different VLANs?ITExamAnswers asked 2 years ago • CCNA 3 v4In which situation could individual router physical interfaces be used for InterVLAN routing, instead of a router-on-a-stick configuration?ITExamAnswers asked 2 years ago • CCNA 3 v4