IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it IT Questions Bank › Category: CCNAWhich type of OSPF LSA represents an external route and is propagated across the entire OSPF domain?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. If no router ID was manually configured, what would router Branch1 use as its OSPF router ID?ITExamAnswers asked 4 years ago • CCNA, CCNPWhy is MD5 authentication more secure than simple authentication for OSPF updates?ITExamAnswers asked 4 years ago • CCNA, CCNPIn an OSPFv2 configuration, what is the effect of entering the command network 192.168.1.1 0.0.0.0 area 0?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. An administrator attempts to configure EIGRP for IPv6 on a router and receives the error message that is shown. Which command must be issued by the administrator before EIGRP for IPv6 can be configured?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. An administrator is trying to configure R1 to run OSPFv3 but the neighbor adjacency is not forming with the router connected to Fa0/0. What is the cause of the problem?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. From what location have the syslog messages been retrieved?ITExamAnswers asked 4 years ago • CCNA, CCNPA network administrator has configured a router for stateless DHCPv6 operation. However, users report that workstations are not receiving DNS server information. Which two router configuration lines should be verified to ensure that stateless DHCPv6 service is properly configured? (Choose two.)ITExamAnswers asked 4 years ago • CCNA, CCNPFor troubleshooting missing EIGRP routes on a router, what three types of information can be collected using the show ip protocols command? (Choose three.)ITExamAnswers asked 4 years ago • CCNAA network administrator is troubleshooting the EIGRP routing between two routers, R1 and R2. The problem is found to be that only some, but not all networks attached to R1 are listed in the routing table of router R2. What should the administrator investigate on router R1 to determine the cause of the problem?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. Two routers have been configured to use EIGRP. Packets are not being forwarded between the two routers. What could be the problem?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. The routing table on R2 does not include all networks that are attached to R1. The network administrator verifies that the network statement is configured to include these two networks. What is a possible cause of the issue?ITExamAnswers asked 4 years ago • CCNA, CCNPA company uses the method SLAAC to configure IPv6 addresses for the workstations of the employees. A network administrator configured the IPv6 address on the LAN interface of the router. The interface status is UP. However, the workstations on the LAN segment did not obtain the correct prefix and prefix length. What else should be configured on the router that is attached to the LAN segment for the workstations to obtain the information?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. A SNMP manager has IP address 172.16.1.120. The SNMP manager is unable to change configuration variables on the R1 SNMP agent. What could be the problem?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. A network administrator is implementing stateful DHCPv6 operation for the company. However, the clients are not using the prefix and prefix-length information that is configured in the DHCP pool. The administrator issues a show ipv6 interface command. What could be the cause of the problem?ITExamAnswers asked 4 years ago • CCNA, CCNP