IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it IT Questions Bank › Category: CCNAWhich of the following routing protocols is considered to use link-state logic?ITExamAnswers asked 2 years ago • CCNAA LAN design uses a Layer 3 EtherChannel between two switches SW1 and SW2, with port-channel interface 1 used on both switches. SW1 uses ports G0/1 and G0/2 in the channel. However, only interface G0/1 is bundled into the channel and working. Think about the configuration settings on port G0/2 that could have existed before adding G0/2 to the EtherChannel. Which answers identify a setting that could prevent IOS from adding G0/2 to the Layer 3 EtherChannel? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNAA LAN design uses a Layer 3 EtherChannel between two switches SW1 and SW2, with port-channel interface 1 used on both switches. SW1 uses ports G0/1, G0/2, and G0/3 in the channel. Which of the following are true about SW1’s configuration to make the channel be able to route IPv4 packets correctly? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNAAn engineer has successfully configured a Layer 3 switch with SVIs for VLANs 2 and 3. Hosts in the subnets using VLANs 2 and 3 can ping each other with the Layer 3 switch routing the packets. The next week, the network engineer receives a call that those same users can no longer ping each other. If the problem is with the Layer 3 switching function, which of the following could have caused the problem? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNAA Layer 3 switch has been configured to route IP packets between VLANs 1, 2, and 3 using SVIs, which connect to subnets 172.20.1.0/25, 172.20.2.0/25, and 172.20.3.0/25, respectively. The engineer issues a show ip route connected command on the Layer 3 switch, listing the connected routes. Which of the following answers lists a piece of information that should be in at least one of the routes?ITExamAnswers asked 2 years ago • CCNARouter R1 has a router-on-a-stick (ROAS) configuration with two subinterfaces of interface G0/1: G0/1.1 and G0/1.2. Physical interface G0/1 is currently in a down/down state. The network engineer then configures a shutdown command when in interface configuration mode for G0/1.1 and a no shutdown command when in interface configuration mode for G0/1.2. Which answers are correct about the interface state for the subinterfaces? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNARouter 1 has a Fast Ethernet interface 0/0 with IP address 10.1.1.1. The interface is connected to a switch. This connection is then migrated to use 802.1Q trunking. Which of the following commands could be part of a valid configuration for Router 1’s Fa0/0 interface? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNARouter R1 lists a route in its routing table. Which of the following answers list a fact from a route that the router uses when matching the packet’s destination address? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNAA router lists the following partial output from the show ip route command. Out which interface will the router route packets destined to IP address 10.1.15.122?ITExamAnswers asked 2 years ago • CCNAA network engineer configures the ip route 10.1.1.0 255.255.255.0 s0/0/0 command on a router and then issues a show ip route command from enable mode. No routes for subnet 10.1.1.0/24 appear in the output. Which of the following could be true?ITExamAnswers asked 2 years ago • CCNAWhich of the following commands correctly configures a static route?ITExamAnswers asked 2 years ago • CCNAAn engineer configures a static IPv4 route on Router R1. Which of the following pieces of information should not be listed as a parameter in the configuration command that creates this static IPv4 route?ITExamAnswers asked 2 years ago • CCNAAfter configuring a working router interface with IP address/mask 10.1.1.100/26, which of the following routes would you expect to see in the output of the show ip route command? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNAWhich of the following is different on the Cisco switch CLI for a Layer 2 switch as compared with the Cisco router CLI?ITExamAnswers asked 2 years ago • CCNAWhich of the following commands do not list the IP address and mask of at least one interface? (Choose two answers.)ITExamAnswers asked 2 years ago • CCNA