IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it IT Questions Bank › Category: CCNPA network administrator has configured a router for stateless DHCPv6 operation. However, users report that workstations are not receiving DNS server information. Which two router configuration lines should be verified to ensure that stateless DHCPv6 service is properly configured? (Choose two.)ITExamAnswers asked 4 years ago • CCNA, CCNPWhile troubleshooting an EIGRP problem on a router, a network engineer needs to verify the IPv4 EIGRP implementation. To check the IP addressing, queue counts, and hold times for the adjacent routers, which command should be used?ITExamAnswers asked 3 years ago • CCNPRefer to the exhibit. R3 has two possible paths to the 172.16.99.0 network. What is the missing value of this output?ITExamAnswers asked 3 years ago • CCNPA network administrator is troubleshooting the EIGRP routing between two routers, R1 and R2. The problem is found to be that only some, but not all networks attached to R1 are listed in the routing table of router R2. What should the administrator investigate on router R1 to determine the cause of the problem?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. Two routers have been configured to use EIGRP. Packets are not being forwarded between the two routers. What could be the problem?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. The routing table on R2 does not include all networks that are attached to R1. The network administrator verifies that the network statement is configured to include these two networks. What is a possible cause of the issue?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. After the configuration shown is applied on router R1, the exhibited status message is displayed. Router R1 is unable to form a neighbor relationship with R2 on the serial 0/1/0 interface. What is the most likely cause of this problem?ITExamAnswers asked 4 years ago • CCNPA network student intern is asked to clean the system settings and upgrade the IOS on a Cisco router. The student uses a Windows 10 laptop and a rollover cable to connect to the console port of the router. The student powers on the router and opens the TeraTerm program. However, the program does not receive any response from the router. What are two possible causes for this problem? (Choose two.)IT Administrator asked 3 years ago • CCNPA company uses the method SLAAC to configure IPv6 addresses for the workstations of the employees. A network administrator configured the IPv6 address on the LAN interface of the router. The interface status is UP. However, the workstations on the LAN segment did not obtain the correct prefix and prefix length. What else should be configured on the router that is attached to the LAN segment for the workstations to obtain the information?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. A network administrator has configured router R1 to send syslog messages to the syslog server. Why is the syslog server unable to receive any logging messages?IT Administrator asked 3 years ago • CCNPA network administrator has verified that timestamps are not appearing with syslog messages on a router. What is the most likely reason for this?IT Administrator asked 3 years ago • CCNPA network technician opens PuTTY to connect to a Cisco switch. The technician sets PuTTY with the IP address of the switch and port 23. However, connections to the switch are always declined. What is a possible cause for this issue?IT Administrator asked 3 years ago • CCNPWhich two types of probes can be configured to monitor traffic by IP SLA within a network environment? (Choose two.)ITExamAnswers asked 4 years ago • CCNPRefer to the exhibit. A SNMP manager has IP address 172.16.1.120. The SNMP manager is unable to change configuration variables on the R1 SNMP agent. What could be the problem?ITExamAnswers asked 4 years ago • CCNA, CCNPA network administrator is configuring SSH on a router. When verifying the configuration, the administrator notices that the SSH connection requests fail, but the Telnet connection requests from the same workstation are successful. Which two parts of the router configuration should be checked to try to locate the problem? (Choose two.)ITExamAnswers asked 3 years ago • CCNP