IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it IT Questions Bank › Category: CCNPRefer to the exhibit. LTC has an OSPF neighbor relationship with the router LTA over the 203.0.113.12/30 network. The 203.0.113.16/30 network link should serve as a backup when the OSPF link goes down. The floating static route command ip route 0.0.0.0 0.0.0.0 S0/1/1 100 was issued on LTC and now traffic is using the backup link even when the OSPF link is up and functioning. Which change should be made to the static route command so that traffic will only use the OSPF link when it is upITExamAnswers asked 3 years ago • CCNPA network engineer is tracing packets through the network but packets are not load balancing over paths as expected. What are two actions the engineer should take? (Choose two.)ITExamAnswers asked 3 years ago • CCNPWhich command should be used to check the OSPF process ID, the router ID, networks the router is advertising, the neighbors the router is receiving updates from, and the default administrative distance?ITExamAnswers asked 4 years ago • CCNPRefer to the exhibit. An administrator is attempting to install an IPv6 static route on router R1 to reach the network attached to router R2. After the static route command is entered, connectivity to the network is still failing. What error has been made in the static route configuration?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. Router CiscoVille has been partially configured for EIGRP authentication. What is missing that would allow successful authentication between EIGRP neighbors?ITExamAnswers asked 4 years ago • CCNA, CCNPWhich destination address is used by EIGRP for IPv6 messages?ITExamAnswers asked 3 years ago • CCNPRefer to the exhibit. A network administrator configures AAA authentication on router R1. The ACS servers are configured and running. The administrator tests the configuration by telneting to R1. What will happen if the administrator attempts to authenticate through the RADIUS server using incorrect credentials?IT Administrator asked 3 years ago • CCNA Security, CCNPRefer to the exhibit. A network administrator issues the show run | section username|aaa|line|radius command to verify an AAA configuration on a Cisco router. Which two conclusions can be drawn from the command output? (Choose two.)IT Administrator asked 3 years ago • CCNPRefer to the exhibit. Both routers R1 and R2 are configured for OSPFv3 and are routing for both IPv4 and IPv6 address families. Which two destination addresses will R1 use to establish a full adjacency with R2? (Choose two.)ITExamAnswers asked 4 years ago • CCNPRefer to the exhibit. Router R1 was configured by a network administrator to use SNMP version 2. The following commands were issued: Why is the administrator not able to get any information from R1?ITExamAnswers asked 4 years ago • CCNA, CCNPRefer to the exhibit. The total number of packet flows is not consistent with what is expected by the network administrator. The results show only half of the flows that are typically captured for the interface. Pings between the router and the collector are successful. What is the reason for the unexpected results?ITExamAnswers asked 4 years ago • CCNPRefer to the exhibit. A network administrator issues the command show bgp ipv6 unicast | begin Network to check the BGP table. Which statement describes the routes with an unspecified address (::) in the Next Hop column?ITExamAnswers asked 4 years ago • CCNPWhen an unlabeled packet arrives at an MPLS-enabled router interface, which database is used to make a forwarding decision on the packet?IT Administrator asked 3 years ago • CCNPMatch the MPLS router type to its characteristic.IT Administrator asked 3 years ago • CCNPRefer to the exhibit. A network administrator configured a class map as shown, but the traffic is not being classified as desired. Which conclusion can be drawn from this configuration?IT Administrator asked 3 years ago • CCNP