IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it IT Questions Bank › Category: CCNA 2 v4An administrator is configuring Router1 so that it can connect to Router2 by using IP. Which protocol can be used by Router1 to determine the IP address of Router2 when they are directly connected and only Layer 2 connectivity exists between them?ITExamAnswers asked 11 months ago • CCNA 2 v4Which two statements are true for OSPF Hello packets? (Choose two.)ITExamAnswers asked 11 months ago • CCNA 2 v4Refer to the exhibit. RIPv1 has been used as a routing protocol on the network. A new 172.16.2.0/24 network has been added on router R2 and configured under the RIP routing process. When will R1 converge?ITExamAnswers asked 11 months ago • CCNA 2 v4Which routing protocol by default uses bandwidth and delay to calculate the metric of a route?ITExamAnswers asked 11 months ago • CCNA 2 v4Refer to the exhibit. Which two routes are level 1 ultimate routes? (Choose two.)ITExamAnswers asked 11 months ago • CCNA 2 v4Refer to the exhibit. Router R1 receives a packet for destination 192.168.1.10. Which route will be preferred for this packet?ITExamAnswers asked 11 months ago • CCNA 2 v4Refer to the exhibit. The IP addresses on all interfaces on router R1 were configured before the OSPF protocol had been enabled on the router. No OSPF router ID was manually configured. Which IP address will be selected by the router as an OSPF router ID?ITExamAnswers asked 2 years ago • CCNA 2 v4Refer to the exhibit. OSPF is used for the routing protocol and all interfaces are configured with the correct IP addresses and subnet masks. During testing, it is found that router R1 is unable to form an adjacency with R2. What is the cause of this problem?ITExamAnswers asked 11 months ago • CCNA 2 v4Refer to the exhibit. When the show cdp neighbors command is issued from router C, which devices will be displayed in the output?ITExamAnswers asked 11 months ago • CCNA 2 v4Refer to the exhibit. The network is using the RIPv2 routing protocol. If network 10.0.0.0 goes down, what mechanism will prevent Router1 from advertising false routing information back to Router2?ITExamAnswers asked 11 months ago • CCNA 2 v4A company is using static routes that are configured with an administrative distance of “1” on all routers in the network. The network administrator decides to introduce a dynamic routing protocol to reduce the manual configurations for the static routes. Which option identifies the correct procedure for the dynamic routing to take place in the network?ITExamAnswers asked 11 months ago • CCNA 2 v4The network administrator configures the router with the ip route 172.16.1.0 255.255.255.0 172.16.2.2 command. How will this route appear in the routing table?ITExamAnswers asked 4 years ago • CCNA, CCNA 2 v4, CCNA 2 v6, CCNA 2 v7, CCNPRefer to the exhibit. The show cdp neighbors command was run on one of the devices as shown. Based on this information, which two facts can be determined? (Choose two.)ITExamAnswers asked 11 months ago • CCNA 2 v4When the engineer enters the show ip route command on R1, the routing table does not display the static route to the 10.1.1.0 network. All R1 and R2 interfaces are correctly addressed per the graphic. What is a logical next step that the engineer could take in order to make the static route display in the routing table in R1?ITExamAnswers asked 11 months ago • CCNA 2 v4Refer to the exhibit. A network administrator accesses router R1 from the console port to configure a newly connected interface. What passwords will the network administrator need to enter to make the connection and the necessary configuration changes?ITExamAnswers asked 11 months ago • CCNA 2 v4