IT Questions Bank Mar 16, 2020 Last Updated: Jun 29, 2023 No Comments Share Tweet Share Pin it IT Questions Bank › Category: CCNPWhich ICMPv6 message type contains network configuration information for clients that are performing SLAAC?IT Administrator asked 3 years ago • CCNP, Network Addressing and Basic TroubleshootingHow many levels of priority are possible when using class of service (CoS) marking on frames?ITExamAnswers asked 4 years ago • CCNP, CCNA, CCNA 4 v6What happens when an edge router using IntServ QoS determines that the data pathway cannot support the level of QoS requested?IT Administrator asked 3 years ago • CCNP, CCNA, CCNA 4 v6What functionality is required on routers to provide remote workers with VoIP and video-conferencing capabilities?ITExamAnswers asked 2 years ago • CCNA, CCNA 3 v7, CCNA 4 v6, CCNPA network administrator has issued the snmp-server user admin1 admin v3 encrypted auth md5 abc789 priv des 256 key99 command. What are two features of this command? (Choose two.)ITExamAnswers asked 4 years ago • CCNA, CCNA 4 v6, CCNPWhich three implicit access control entries are automatically added to the end of an IPv6 ACL? (Choose three.)ITExamAnswers asked 4 years ago • CCNA, CCNA 4 v6, CCNPWhich feature is unique to IPv6 ACLs when compared to those of IPv4 ACLs?ITExamAnswers asked 4 years ago • CCNA, CCNA 4 v6, CCNA Security, CCNPWhich IPv6 ACL command entry will permit traffic from any host to an SMTP server on network 2001:DB8:10:10::/64?ITExamAnswers asked 4 years ago • CCNA, CCNA 4 v6, CCNPWhich two characteristics are shared by both standard and extended ACLs? (Choose two.)ITExamAnswers asked 4 years ago • CCNA, CCNA 4 v6, CCNA Security, CCNPWhich three statements describe ACL processing of packets? (Choose three.)ITExamAnswers asked 4 years ago • CCNP, CCNA, CCNA 2 v6, CCNA 4 v4, CCNA 4 v6, CCNA SecurityWhich remote access implementation scenario will support the use of generic routing encapsulation tunneling?ITExamAnswers asked 4 years ago • CCNP, CCNA 4 v6A network engineer is troubleshooting an OSPFv2 network and discovers that two routers connected by a point-to-point WAN serial link are not establishing an adjacency. The OSPF routing process, network commands and area ID are all confirmed as correct, and the interfaces are not passive. Testing shows that the cabling is correct, that the link is up, and pings between the interfaces are successful. What is most likely the problem?ITExamAnswers asked 4 years ago • CCNA, CCNA 3 v6, CCNPWhich command is used to verify that OSPF is enabled and also provides a list of the networks that are being advertised by the network?ITExamAnswers asked 4 years ago • CCNA, CCNA 3 v6, CCNPA network engineer is troubleshooting convergence and adjacency issues in an OSPFv2 network and has noted that some expected network route entries are not displayed in the routing table. Which two commands will provide additional information about the state of router adjacencies, timer intervals, and the area ID? (Choose two.)ITExamAnswers asked 4 years ago • CCNA, CCNA 3 v6, CCNPWhich command can be used to verify the contents of the LSDB in an OSPF area?ITExamAnswers asked 4 years ago • CCNA, CCNA 3 v6, CCNA 3 v7, CCNP