7.3.2.7 Packet Tracer – Cable a Simple Network (Answers)

7.3.2.7 Packet Tracer – Cable a Simple Network (Answers)

Objectives

  • Develop an understanding of the basic functions of Packet Tracer.
  • Create a simple network with two hosts.
  • Observe the importance of using the correct cable type to connect PCs.

Hint: To ensure that the instructions always remain visible during an activity, click the Top check box in the lower left-hand corner of this instruction window.

Step 1: Create a network diagram with two PCs.

The bottom left-hand corner of the Packet Tracer screen displays icons that represent device categories or groups, such as Routers, Switches, or End Devices.

Move your cursor over the device categories to show the name of the category in the box centered between the rows of devices. To select a device, first select the device category. Once the device category is selected, the options within that category appear in the box next to the category listings. Select the device option that is required.

a. Select End Devices from the options in the bottom left-hand corner.

b. Drag and drop two generic PCs (PC-PT) onto the Logical Workspace.

c. Select Connections from the bottom left-hand corner.

d. Choose a Copper Straight-Through cable type.

e. Click the first host, PC0, and assign the cable to the FastEthernet connector.

f. Click the second host, PC1, and assign the cable to the FastEthernet connector.

g. The red dots indicate an incorrect cable type. Click the red X on the right-hand side of Packet Tracer. This will allow you to delete the Copper Straight-Through cable.

h. Move the cursor to the cable and click the cable to delete it.

i. Choose a Copper Cross-Over cable type.

j. Click the first host, PC0, and assign the cable to the FastEthernet connector.

k. Click the second host, PC1, and assign the cable to the FastEthernet connector. The green dots at both ends of the cable indicate the correct cable type.

Step 2: Configure host names and IP addresses on the PCs.

a. Click PC0. A PC0 window will appear.

b. From the PC0 window, select the Config tab.

c. Change the PC Display Name to PC-A.

d. Select the FastEthernet0 tab on the left.

e. Type the IP address 192.168.1.1 and subnet mask 255.255.255.0 in the IP Configuration section.

f. Close the PC-A configuration window by selecting the X in the upper right-hand corner.

g. Click PC1. A PC1 window will open.

h. From the PC1 window, select the Config tab.

i. Change the PC Display Name to PC-B.

j. Select the FastEthernet0 tab on the left.

k. Type the IP address 192.168.1.2 and subnet mask 255.255.255.0 in the IP Configuration section.

l. Click PC-A and then click the Desktop tab.

m. Click Command Prompt.

n. Type ping 192.168.1.2. This is the address of the other computer.

o. Close the PC-B configuration window by selecting the X in the upper right-hand corner.

Step 3: Connect the computers to a switch.

a. Delete the Copper Cross-Over cable.

b. Select Switches from the options in the bottom left-hand corner.

c. Drag and drop a 2960 switch onto the Logical Workspace.

d. Select Connections from the bottom left-hand corner.

e. Choose a Copper Straight-Through cable type.

f. Click the first host, PC-A, and assign the cable to the FastEthernet0 connector.

g. Click the switch, Switch0, and select a connection port, FastEthernet0/1, to connect to PC-A. After about one minute, two green dots should appear on both sides of the Copper Straight-Through cable. This indicates the correct cable type has been used.

h. Click the Copper Straight-Through cable type again.

i. Click the second host, PC-B, and assign the cable to the FastEthernet0 connector.

j. Click the switch, Switch0, and click FastEthernet0/2 to connect to PC-B.

k. Click PC-B and then click the Desktop tab.

l. Click Command Prompt.

m. Type ping 192.168.1.1. This is the address of the other computer.

n. Click the Check Results button at the bottom of this instruction window to verify that the topology is correct.

Your completion percentage should be 100 percent. The Assessment Items tab shows the scoring of each item in this activity.

Download 7.3.2.7 Packet Tracer – Cable a Simple Network PDF & PKA files:


Subscribe
Notify of
guest

0 Comments
Inline Feedbacks
View all comments
0
Would love your thoughts, please comment.x
()
x