Time limit: 0
Quiz-summary
0 of 24 questions completed
Questions:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
Information
Good Luck!
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
Results
0 of 24 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0)
Average score |
|
Your score |
|
Categories
- Not categorized 0%
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- Answered
- Review
-
Question 1 of 24
1. Question
1 pointsWhich statement describes the port speed LED on the Cisco Catalyst 2960 switch?Correct
Incorrect
Hint
The port speed LED indicates that the port speed mode is selected. When selected, the port LEDs will display colors with different meanings. If the LED is off, the port is operating at 10 Mb/s. If the LED is green, the port is operating at 100 Mb/s. If the LED is blinking green, the port is operating at 1000 Mb/s. -
Question 2 of 24
2. Question
1 pointsWhich command is used to set the BOOT environment variable that defines where to find the IOS image file on a switch?Correct
Incorrect
Hint
The boot system command is used to set the BOOT environment variable. The config-register and confreg commands are used to set the configuration register. The boot loader command supports commands to format the flash file system, reinstall the operating system software, and recover from a lost or forgotten password. -
Question 3 of 24
3. Question
1 pointsWhat is a function of the switch boot loader?Correct
Incorrect
Hint
The switch boot loader environment is presented when the switch cannot locate a valid operating system. The boot loader environment provides a few basic commands that allows a network administrator to reload the operating system or provide an alternate location of the operating system. -
Question 4 of 24
4. Question
1 pointsWhich interface is the default location that would contain the IP address used to manage a 24-port Ethernet switch?Correct
Incorrect
-
Question 5 of 24
5. Question
1 pointsA production switch is reloaded and finishes with a Switch> prompt. What two facts can be determined? (Choose two.)Correct
Incorrect
-
Question 6 of 24
6. Question
1 pointsWhich two statements are true about using full-duplex Fast Ethernet? (Choose two.) Performance is improved with bidirectional data flow.*Correct
Incorrect
-
Question 7 of 24
7. Question
1 pointsIn which situation would a technician use the show interfaces switch command?Correct
Incorrect
Hint
The show interfaces command is useful to detect media errors, to see if packets are being sent and received, and to determine if any runts, giants, CRCs, interface resets, or other errors have occurred. Problems with reachability to a remote network would likely be caused by a misconfigured default gateway or other routing issue, not a switch issue. The show mac address-table command shows the MAC address of a directly attached device. -
Question 8 of 24
8. Question
1 pointsRefer to the exhibit. A network technician is troubleshooting connectivity issues in an Ethernet network with the command show interfaces fastEthernet 0/0. What conclusion can be drawn based on the partial output in the exhibit?Correct
Incorrect
Hint
The partial output shows that there are 50 giants (frames longer than the allowed maximum) that were injected into the network, possibly by a malfunctioning NIC. This conclusion can be drawn because there are only 25 collisions, so not all the 50 giants are the result of a collision. Also, because there 25 collisions, it is most likely that not all hosts are using full-duplex mode (otherwise there would not be any collisions). There should be no cabling issues since the CRC error value is 0. There are 0 runts, so the collisions have not caused malformed frames to occur that are shorter than 64 bytes in length . -
Question 9 of 24
9. Question
1 pointsRefer to the exhibit. What media issue might exist on the link connected to Fa0/1 based on the show interface command?Correct
Incorrect
Hint
Escalating CRC errors usually means that the data is being modified during transmission from the host to the switch. This is often caused by high levels of electromagnetic interference on the link. -
Question 10 of 24
10. Question
1 pointsIf one end of an Ethernet connection is configured for full duplex and the other end of the connection is configured for half duplex, where would late collisions be observed?Correct
Incorrect
Hint
Full-duplex communications do not produce collisions. However, collisions often occur in half-duplex operations. When a connection has two different duplex configurations, the half-duplex end will experience late collisions. Collisions are found on Ethernet networks. Serial interfaces use technologies other than Ethernet. -
Question 11 of 24
11. Question
1 pointsWhat is one difference between using Telnet or SSH to connect to a network device for management purposes?Correct
Incorrect
Hint
SSH provides security for remote management connections to a network device. SSH does so through encryption for session authentication (username and password) as well as for data transmission. Telnet sends a username and password in plain text, which can be targeted to obtain the username and password through data capture. Both Telnet and SSH use TCP, support authentication, and connect to hosts in CLI. -
Question 12 of 24
12. Question
1 pointsRefer to the exhibit. The network administrator wants to configure Switch1 to allow SSH connections and prohibit Telnet connections. How should the network administrator change the displayed configuration to satisfy the requirement?Correct
Incorrect
-
Question 13 of 24
13. Question
1 pointsWhat is the effect of using the switchport port-security command?Correct
Incorrect
Hint
Port security cannot be enabled globally. All active switch ports should be manually secured using the switchport port-security command, which allows the administrator to control the number of valid MAC addresses allowed to access the port. This command does not specify what action will be taken if a violation occurs, nor does it change the process of populating the MAC address table. -
Question 14 of 24
14. Question
1 pointsWhere are dynamically learned MAC addresses stored when sticky learning is enabled with the switchport port-security mac-address sticky command?Correct
Incorrect
Hint
When MAC addresses are automatically learned by using the sticky command option, the learned MAC addresses are added to the running configuration, which is stored in RAM. -
Question 15 of 24
15. Question
1 pointsA network administrator configures the port security feature on a switch. The security policy specifies that each access port should allow up to two MAC addresses. When the maximum number of MAC addresses is reached, a frame with the unknown source MAC address is dropped and a notification is sent to the syslog server. Which security violation mode should be configured for each access port?Correct
Incorrect
Hint
In port security implementation, an interface can be configured for one of three violation modes: Protect – a port security violation causes the interface to drop packets with unknown source addresses and no notification is sent that a security violation has occurred. Restrict – a port security violation causes the interface to drop packets with unknown source addresses and to send a notification that a security violation has occurred. Shutdown – a port security violation causes the interface to immediately become error-disabled and turns off the port LED. No notification is sent that a security violation has occurred. -
Question 16 of 24
16. Question
1 pointsWhich two statements are true regarding switch port security? (Choose two.)Correct
Incorrect
-
Question 17 of 24
17. Question
1 pointsWhich action will bring an error-disabled switch port back to an operational state?Correct
Incorrect
Hint
When a violation occurs on a switch port that is configured for port security with the shutdown violation action, it is put into the err-disabled state. It can be brought back up by shutting down the interface and then issuing the no shutdown command. -
Question 18 of 24
18. Question
1 pointsRefer to the exhibit. Port Fa0/2 has already been configured appropriately. The IP phone and PC work properly. Which switch configuration would be most appropriate for port Fa0/2 if the network administrator has the following goals? No one is allowed to disconnect the IP phone or the PC and connect some other wired device. If a different device is connected, port Fa0/2 is shut down. The switch should automatically detect the MAC address of the IP phone and the PC and add those addresses to the running configuration.Correct
Incorrect
Hint
The default mode for a port security violation is to shut down the port so the switchport port-security violation command is not necessary. The switchport port-security command must be entered with no additional options to enable port security for the port. Then, additional port security options can be added. -
Question 19 of 24
19. Question
1 pointsRefer to the exhibit. What can be determined about port security from the information that is shown?Correct
Incorrect
Hint
The Port Security line simply shows a state of Enabled if the switchport port-security command (with no options) has been entered for a particular switch port. If a port security violation had occurred, a different error message appears such as Secure-shutdown. The maximum number of MAC addresses supported is 50. The Maximum MAC Addresses line is used to show how many MAC addresses can be learned (2 in this case). The Sticky MAC Addresses line shows that only one device has been attached and learned automatically by the switch. This configuration could be used when a port is shared by two cubicle-sharing personnel who bring in separate laptops. -
Question 20 of 24
20. Question
1 pointsRefer to the exhibit. Which event will take place if there is a port security violation on switch S1 interface Fa0/1?Correct
Incorrect
Hint
Interface FastEthernet 0/1 is configured with the violation mode of protect. If there is a violation, interface FastEthernet 0/1 will drop packets with unknown MAC addresses. -
Question 21 of 24
21. Question
1 pointsOpen the PT Activity. Perform the tasks in the activity instructions and then answer the question. Which event will take place if there is a port security violation on switch S1 interface Fa0/1?Correct
Incorrect
Hint
The violation mode can be viewed by issuing the show port-security interface command. Interface FastEthernet 0/1 is configured with the violation mode of protect. If there is a violation, interface FastEthernet 0/1 will drop packets with unknown MAC addresses. -
Question 22 of 24
22. Question
1 pointsFill in the blank.- Do not use abbreviations.What is the missing command on S1? (ip address 192.168.99.2 255.255.255.0)
Correct
Incorrect
-
Question 23 of 24
23. Question
1 pointsMatch the step to each switch boot sequence description. (Not all options are used.)Sort elements
- execute POST
- load the boot loader from ROM
- CPU register initializations
- flash file system initialization
- load the IOS
- transfer switch control to the IOS
- enter global configuration mode
-
step 1
-
step 2
-
step 3
-
step 4
-
step 5
-
step 6
Correct
Incorrect
-
Question 24 of 24
24. Question
1 pointsIdentify the steps needed to configure a switch for SSH. The answer order does not matter. (Not all options are used.)Sort elements
- Create a local user.
- Generate RSA keys.
- Configure a domain name.
- Use the login local command.
- Use the transport input ssh command.
- Order does not matter within this group.
- Use the login command
- Use the password cisco command
-
SSH configuration step
-
SSH configuration step
-
SSH configuration step
-
SSH configuration step
-
SSH configuration step
-
SSH configuration step
Correct
Incorrect
Hint
The login and password cisco commands are used with Telnet switch configuration, not SSH configuration.