CCNP ROUTE Final Test online (Version 7) – Score 100%

Refer to the exhibit. All routers are configured for OSPF area 0. The network administrator requires that R2 always be the DR and maintain adjacency. Which two configurations can achieve this? (Choose two.)

Refer to the exhibit. Routers A and B have EIGRP configured and automatic summarization has been disabled on both routers. Which two router commands should be used to summarize the attached routes, and to which interface is this command applied? (Choose two.)

Refer to the exhibit. Router R1 is seeing routes that are advertised by router R2, and R2 is seeing routes that are advertised by R1. Which two statements are true when using EIGRP and an L3 MPLS VPN? (Choose two.)

Which two EIGRP and MPLS implementation statements are true? (Choose two.)

What are two effective ways to prevent the EIGRP stuck-in-active problem? (Choose two.)

On an OSPF multiaccess network, which multicast address must a non-DR router use to send an LSU packet that contains new link-state information?

Which two variables must match between two OSPF routers to form a neighbor adjacency? (Choose two.)

Refer to the exhibit. A network administrator is troubleshooting a recent OSPF stub configuration between R3 and R4. The only routes that should appear on the routing table for R4 are intra-area routes and the default route. However, interarea routes are also appearing. What must the administrator do to fix this problem?

Refer to the exhibit. Which two commands need to be used on R1 and R2 to create a virtual link to and from area 0? (Choose two.)

Refer to the exhibit. The BGP sessions are established between all routers. RTC receives route updates for network 170.10.0.0 from autonomous system 300 with the weight attribute set to 3000. RTB learns about network 170.10.0.0 from autonomous system 200 with a weight of 2000. Which router will be used by RTA as a next hop to reach network 170.10.0.0?

Refer to the exhibit. RTR-A and RTR-B cannot establish a BGP relationship. What could be the problem?

Refer to the exhibit. Assume router R2 does not have BGP enabled. However, the neighbor remote-as router configuration command has been entered on routers R1 and R3. Based on the information that is presented, which two statements are true? (Choose two.)

What is a characteristic of an IBGP session type?

Refer to the exhibit. Assume all routers are running BGP sessions and both links are operational. Which procedure would ensure that AS1 routers use link 1.1.1.1 for packet transmittal to AS2?

Which statement about stateless autoconfiguration is true?

Assume that the ipv6 unicast-routing global configuration command has already been applied on a router. What is the effect of entering the ipv6 ospf 1 area 1 interface configuration command?

Which ICMPv6 message provides prefix, prefix length and default gateway information for an IPv6 device?

Which mechanism optimizes the TCP window size by multiplying the product of the bandwidth times the round-trip delay?

Which command is used by a router to only announce a default route in it’s RIPng updates?

Which type of address is used to send traffic to a group of devices?

What is the IPv4 multicast address used by EIGRP?

Which VPN solution is used to better scale large IPsec hub-to-spoke and spoke-to-spoke networks?

What must be done before RIPng can be enabled?

In which routing protocol and type of active interface automatically enabled for that routing protocol? Choose two.

Which IGP routing protocols use a 32-bit router-ID? Choose all that apply.

Which command is used to enable OSPFv3 using address families on an interface?

Which statement is true concerning OSPF messages when using OSPFv3 with address families?

Which IPv6 multicast addresses are used by OSPFv3?

Refer to the exhibit. Which two statements are correct for the route map that is shown? (Choose two.)

Refer to the exhibit. Which route redistribution statement is true?

Which route map configuration command matches routes identified by an ACL or an prefix list?

Which two networks would match the following prefix list? (Choose two.)ip prefix-list MATCHTHIS seq 5 deny 10.1.0.0/16 ge 24 le 30

Refer to the exhibit. Which three actions will be results of the distribute list that is shown? (Choose three.)

Which routing updates would be permitted when the distribute-list 1 in serial 0/0/0 router configuration command is configured?

Which set of commands correctly configures one-way route redistribution from OSPF into the EIGRP routing domain?

Which two statements are correct about redistribution? (Choose two.)

Which statement best describes the route filtering process used by route maps?

Which two OSPF routing protocol characteristics can be used or modified at redistribution points to help implement a path control strategy? (Choose two.)

Which routes will retain existing metrics when redistributed into EIGRP?

Which two statements are true of policy-based routing (PBR) as a path control tool? (Choose two.)

Refer to the exhibit. The route map LOAD_BALANCE has been applied to the FastEthernet interfaces of R1, and all interfaces are up. R1 uses two default static routes to reach the Internet via ISP1 and ISP2. Which traffic will be sent to the null 0 interface by the route map on R1?

Which command would allow the filtering of routes for the 10.0.0.0 255.255.0.0 network through the 10.0.255.0 255.255.255.0 network address space?

Refer to the exhibit. The network policy requires that packets from the 10.0.0.0/8 network be directed to R2 to and then the Internet? Given the following configuration: access-list 111 permit ip 10.0.0.0 0.255.255.255 any route-map net-10 permit 10 match ip address 111 set interface FastEthernet 0/1 On which router and which interface would the ip policy route-map command be configured?

What is the purpose of the Cisco IOS IP SLA feature?

Which three of the following packets cannot be CEF switched and must be processed in software?

Which router interface command would enable a router to acquire an IP address configuration from an upstream DHCP server?

The IPv6 _____________________ interface ID is derived by splitting an interface’s 48-bit MAC address in two and inserting 0xFFFE in between the two parts.

Use this interface configuration command to enable the automatic configuration of an IPv6 address using stateless address autoconfiguration (SLAAC).

Which protocol would you use to provide IPv4 Internet connectivity to IPv6 devices?

In MP-BGP, what must be configured within an address family before a neighbor can be established?

Which of the following regarding MP-BGP is not a true statement?

Which statement about SNMP is true?

The output of the show ip ssh command displays “SSH Enabled – version 2”. Based on this output, which statement is true?

Which VRF statement is true?

Which two routing protocol authentication statements are true? (Choose two.)

Which statement about the Secure Copy (SCP) feature is true?