IT Exam Items Repository

A sales representative is preparing to send sensitive information to corporate headquarters from a hotel room using the Internet. Prior to the trip, the IT staff made the necessary provisions to allow secure Internet access. What solution was implemented for the sales representative?
ITExamAnswers Editorial Team asked 3 years ago • 
Refer to the exhibit. The network is using OSPF as the routing protocol. A network administrator issues the show ip ospf neighbor command to check the status of operation. Which statement is true?
ITExamAnswers Editorial Team asked 3 years ago • 
Assuming VLSM is not being used, what impact will adding the command ip route 172.16.64.0 255.255.240.0 serial0/0 have on a router that is already operational in a network?
ITExamAnswers Editorial Team asked 3 years ago • 
What are two characteristics of an extended ACL? (Choose two.)
ITExamAnswers Editorial Team asked 3 years ago • 
In which VTP mode can a switch create VLANs, ignore VTP messages, and not pass local VLAN information to other VTP domain members?
ITExamAnswers Editorial Team asked 3 years ago • 
Which two statements describe when a network administrator should perform a network baseline? (Choose two.)
ITExamAnswers Editorial Team asked 3 years ago • 
Refer to the exhibit. A network administrator has implemented subnetting using the network 192.168.25.0 and a /28 mask. Workstation 1 is not able to ping with Workstation 2. What is a possible cause for this lack of communication?
ITExamAnswers Editorial Team asked 3 years ago • 
Refer to the exhibit. The network administrator is unable to ping from the console of router R3 to host 10.10.4.63. What is the problem?
ITExamAnswers Editorial Team asked 3 years ago • 
Refer to the exhibit. The network administrator correctly configures RTA to perform inter-VLAN routing. Using the show vlan command, the administrator verifies that port Fast Ethernet 0/4 is the first available port in the default VLAN on SW2. The administrator connects RTA to port 0/4 on SW2, but inter-VLAN routing does not work. What could be the possible cause of the problem with the SW2 configuration?
ITExamAnswers Editorial Team asked 3 years ago • 
Refer to the exhibit. A network administrator is troubleshooting a problem. No users are able to access the 10.10.2.0/24 network, but are able to access all other networks. Assuming R3 is configured correctly and based on the output shown, what is most likely the problem?
ITExamAnswers Editorial Team asked 3 years ago • 
Refer to the exhibit. ABC Company is using the 172.16.0.0/18 network. It is standard company practice to use the first 50 addresses for switches and servers and assign the last usable address to the router. The remaining addresses are assigned to the hosts. After assigning the addresses, the network technician tests connectivity from the host above and is not able to ping the router. What could be the problem?
ITExamAnswers Editorial Team asked 3 years ago • 
Refer to the exhibit. The network administrator is troubleshooting the connectivity issue between RA and RB. According to the partial configuration, what is the cause of the problem?
ITExamAnswers Editorial Team asked 3 years ago • 
A network at a large building failed, causing a severe disruption in business activities. The problem was eventually detected and resolved by replacing a piece of failed network equipment. Investigation led to the conclusion that a network design problem was the main cause of the disruption. Loss of a single piece of equipment should not have been able to cause such a large problem. What two terms best describe this type of design weakness? (Choose two.)
ITExamAnswers Editorial Team asked 3 years ago • 
Although all networks are reachable, the network administrator notices abnormal routing behavior after configuring OSPF on each router. According to the partial output from the debug ip ospf events command, which statement is true about the contents of the routing table in RA?
ITExamAnswers Editorial Team asked 3 years ago • 
Refer to the exhibit. An ACL is configured to prevent access by network 192.168.1.0 to network 192.168.2.0, but it is not working properly. What problem is discovered after observing the output of the show running-config command?
ITExamAnswers Editorial Team asked 3 years ago • 
« Previous1…265266267268269…1,378Next »
Ask Question