IT Exam Items Repository

The output of the show interfaces status command on a 2960 switch shows interface Fa0/1 in a “disabled” state. Which of the following is true about interface Fa0/1? (Choose three answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
A Cisco Catalyst switch connects with its Gigabit0/1 port to an end user’s PC. The end user, thinking the user is helping, manually sets the PC’s OS to use a speed of 1000 Mbps and to use full duplex, and disables the use of autonegotiation. The switch’s G0/1 port has default settings for speed and duplex. What speed and duplex settings will the switch decide to use? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
In which of the following modes of the CLI could you configure the duplex setting for interface Fast Ethernet 0/5?
ITExamAnswers Editorial Team asked 4 years ago • 
Which of the following describes a way to disable IEEE standard autonegotiation on a 10/100 port on a Cisco switch?
ITExamAnswers Editorial Team asked 4 years ago • 
Which of the following line subcommands tells a switch to wait until a show command’s output has completed before displaying log messages on the screen?
ITExamAnswers Editorial Team asked 4 years ago • 
A Layer 2 switch configuration places all its physical ports into VLAN 2. The IP addressing plan shows that address 172.16.2.250 (with mask 255.255.255.0) is reserved for use by this new LAN switch and that 172.16.2.254 is already configured on the router connected to that same VLAN. The switch needs to support SSH connections into the switch from any subnet in the network. Which of the following commands are part of the required configuration in this case? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
An engineer’s desktop PC connects to a switch at the main site. A router at the main site connects to each branch office through a serial link, with one small router and switch at each branch. Which of the following commands must be configured on the branch office switches, in the listed configuration mode, to allow the engineer to telnet to the branch office switches and supply only a password to login? (Choose three answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
An engineer had formerly configured a Cisco 2960 switch to allow Telnet access so that the switch expected a password of mypassword from the Telnet user. The engineer then changed the configuration to support Secure Shell. Which of the following commands could have been part of the new configuration? (Choose two answers.)
ITExamAnswers Editorial Team asked 4 years ago • 
An engineer wants to set up simple password protection with no usernames for some switches in a lab, for the purpose of keeping curious coworkers from logging in to the lab switches from their desktop PCs. Which of the following commands would be a useful part of that configuration?
ITExamAnswers Editorial Team asked 4 years ago • 
Imagine that you have configured the enable secret command, followed by the enable password command, from the console. You log out of the switch and log back in at the console. Which command defines the password that you had to enter to access privileged mode?
ITExamAnswers Editorial Team asked 4 years ago • 
Consider the following output from a Cisco Catalyst switch: Which of the following answers is true about this switch?
ITExamAnswers Editorial Team asked 4 years ago • 
A Cisco Catalyst switch has 24 10/100 ports, numbered 0/1 through 0/24. Ten PCs connect to the 10 lowest numbered ports, with those PCs working and sending data over the network. The other ports are not connected to any device. Which of the following answers lists facts displayed by the show interfaces status command?
ITExamAnswers Editorial Team asked 4 years ago • 
Which of the following statements best describes what a switch does with a frame destined for an unknown unicast address?
ITExamAnswers Editorial Team asked 4 years ago • 
Which of the following statements describes part of the process of how a LAN switch decides to forward a frame destined for a broadcast MAC address?
ITExamAnswers Editorial Team asked 4 years ago • 
Which of the following statements describes part of the process of how a switch decides to forward a frame destined for a known unicast MAC address?
ITExamAnswers Editorial Team asked 4 years ago • 
« Previous1…816817818819820…1,378Next »