IT Exam Items Repository

Refer to the exhibit. Which command must be configured to make VRF CCNP work?
ITExam Editorial Team asked 5 years ago • 
Refer to the exhibit. An engineer configured NetFlow on R1, but the NMS server cannot see the flow from ethernet 0/0 of R1. Which configuration resolves the issue?
ITExam Editorial Team asked 5 years ago • 
Refer to the exhibit. A network administrator sets up an OSPF routing protocol for a DMVPN network on the hub router. Which configuration required to establish a DMVPN tunnel with multiple spokes?
ITExam Editorial Team asked 5 years ago • 
Refer to the exhibit. An engineer is troubleshooting a TACACS problem. Which action resolves the issue?
ITExam Editorial Team asked 5 years ago • 
Refer to the exhibit. An engineer configured IP SLA on R1 to avoid the ISP link flapping problem. but it is not working as designed IP SLA should wait 30 seconds before switching traffic to a secondary connection and then revert to the primary link after waning 20 seconds, when the primary link is available and stabilized. Which configuration resolves the issue?
ITExam Editorial Team asked 5 years ago • 
Refer to the exhibit. An engineer configures DMVPN and receives the hub location prefix of 10.1.1.0724 on R2 and R3 The R3 prefix of 10 1.3.0/24 is not received on R2. and the R2 prefix 10.1,2.0/24 is not received on R3. Which action reserves the issue?
ITExam Editorial Team asked 5 years ago • 
Refer to the exhibit. R5 should not receive any routes originated in the EIGRP domain. Which set of configuration changes removes the EIGRP routes from the R5 routing table to fix the issue?
ITExam Editorial Team asked 5 years ago • 
Refer to the exhibit. An engineer configured NetFlow on R1, but the NMS server cannot see the flow from R1. Which configuration resolves the issue?
ITExam Editorial Team asked 5 years ago • 
Refer to the exhibit. A network administrator successfully logs in to a switch using SSH from a (RADIUS server When the network administrator uses a console port to access the switch the RADIUS server returns shell:privlvl=15'' and the switch asks to enter the enable command \ the command is entered, it gets rejected. Which command set is used to troubleshoot and reserve this issue?
ITExam Editorial Team asked 5 years ago • 
Refer to the exhibit. A prefix list is created to filter routes inbound to an EIGRP process except for network 10 prefixes After the prefix list is applied no network 10 prefixes are visible in the routing table from EIGRP. Which configuration resolves the issue?
ITExam Editorial Team asked 5 years ago • 
How does an MPLS Layer 3 VPN differentiate the IP address space used between each VPN?
ITExam Editorial Team asked 5 years ago • 
An engineer is implementing a coordinated change with a server team. As part of the change, the engineer must configure interlace GigabitEthernet2 in an existing VRF "RED" then move the interface to an existing VRF "BLUE" when the server team is ready. The engineer configured interface GigabitEthemet2 in VRF "RED". Which configuration completes the change?
ITExam Editorial Team asked 5 years ago • 
Refer to the exhibit. The ISP router is fully configured for customer A and customer B using the VRF-Lite feature. What is the minimum configuration required for customer A to communicate between routers A1 and A2?
ITExam Editorial Team asked 5 years ago • 
What are the two prerequisites to enable BFD on Cisco routers? (Choose two)
ITExam Editorial Team asked 5 years ago • 
Refer to the exhibit. An OSPF neighbor relationship between R2 and R3 is showing stuck in EXCHANGE/EXSTART state. The neighbor is established between R1 and R2. The network engineer can ping from R2 to R3 and vice versa, but the neighbor is still down. Which action resolves the issue?
ITExam Editorial Team asked 5 years ago • 
« Previous1…948949950951952…1,378Next »