13. Which table is used by EIGRP to store all routes that are learned from EIGRP neighbors? the routing table the neighbor table the topology table the adjacency table 14. Which multicast address does an EIGRP-enabled router use to send query packets? 224.0.0.10 224.0.0.9 224.0.0.12 224.0.0.5 15. Which …
1. Consider the following command: Copyip route 192.168.10.0 255.255.255.0 10.10.10.2 5 What does the 5 at the end of the command signify? metric exit interface administrative distance maximum number of hops to the 192.168.10.0/24 network 2. What type of static route is created when the next-hop IP address …
15.1.2 Lab - Implement NTP (Answers) Topology Addressing Table Device Interface IPv4 Address R1 G0/0/0 172.16.0.2/30 G0/0/1 10.10.0.1/29 R2 G0/0/0 172.16.0.1/30 G0/0/1 172.16.1.1/30 R3 G0/0/0 172.16.1.2/30 D1 G1/0/5 10.10.0.2/29 D2 G1/0/5 10.10.0.3/29 A1 VLAN 1 10.10.0.4/29 Objectives Part 1: Build the Network, Configure Basic Device Settings and Routing …
49. What protocol or technology manages trunk negotiations between switches? DTP STP EtherChannel VTP 50. Refer to the exhibit. An administrator tried to implement an EtherChannel between two switches by grouping the six physical ports as shown. However, the administrator was not successful. What is the reason for …
37. Assuming that all switches in a network have the default bridge priority for each MST instance, what effect does the command spanning-tree mst 10 root primary have when entered on a single switch? sets the bridge priority on the switch to 24586 for MST instance 10 sets …
25. An administrator is troubleshooting a switch and wants to verify if it is a root bridge. What command can be used to do this? show spanning-tree show running-config show startup-config show vlan 26. Which two concepts relate to a switch port that is intended to have only …
13. What additional information is contained in the 12-bit extended system ID of a BPDU? MAC address VLAN ID IP address port ID 14. Refer to the exhibit. Which switch will be the root bridge after the election process is complete? S1 S2 S3 S4 15. Which STP …
1. What are two characteristics of a Layer 2 Ethernet switch access port? (Choose two.) Access mode is the default operating mode for a port on a Layer 2 switch. An access port is associated with a single VLAN. An access port uses 802.1Q frame encapsulation. Access ports …
12.1.3 Lab - Implement BGP Communities (Answers) Topology Addressing Table Device Interface IPv4 Address IPv6 Address IPv6 Link-Local R1 G0/0/0 10.1.2.1/24 2001:db8:acad:1012::1/64 fe80::1:1 S0/1/0 10.1.3.1/25 2001:db8:acad:1013::1/64 fe80::1:2 S0/1/1 10.1.3.129/25 2001:db8:acad:1014::1/64 fe80::1:3 Loopback0 192.168.1.1/27 2001:db8:acad:1000::1/64 fe80::1:4 Loopback1 192.168.1.65/26 2001:db8:acad:1001::1/64 fe80::1:5 R2 G0/0/0 10.1.2.2/24 2001:db8:acad:1012::2/64 fe80::2:1 G0/0/1 10.2.3.2/24 2001:db8:acad:1023::2/64 fe80::2:2 …
12.1.2 Lab - Implement BGP Path Manipulation (Answers) Topology Addressing Table Device Interface IPv4 Address IPv6 Address IPv6 Link-Local R1 G0/0/0 10.1.2.1/24 2001:db8:acad:1012::1/64 fe80::1:1 S0/1/0 10.1.3.1/25 2001:db8:acad:1013::1/64 fe80::1:2 S0/1/1 10.1.3.129/25 2001:db8:acad:1014::1/64 fe80::1:3 Loopback0 192.168.1.1/27 2001:db8:acad:1000::1/64 fe80::1:4 Loopback1 192.168.1.65/26 2001:db8:acad:1001::1/64 fe80::1:5 R2 G0/0/0 10.1.2.2/24 2001:db8:acad:1012::2/64 fe80::2:1 G0/0/1 10.2.3.2/24 2001:db8:acad:1023::2/64 …
