3.4.1.2 Lab – Using Wireshark to View Network Traffic Answers

3.4.1.2 Lab – Using Wireshark to View Network Traffic (Instructor Version – Optional Lab)

Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or to provide additional practice.

Topology

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 31

Objectives

Part 1: Capture and Analyze Local ICMP Data in Wireshark
Part 2: Capture and Analyze Remote ICMP Data in Wireshark

Background / Scenario

Wireshark is a software protocol analyzer, or “packet sniffer” application, used for network troubleshooting, analysis, software and protocol development, and education. As data streams travel back and forth over the network, the sniffer “captures” each protocol data unit (PDU) and can decode and analyze its content according to the appropriate RFC or other specifications.

Wireshark is a useful tool for anyone working with networks and can be used with most labs in the CCNA courses for data analysis and troubleshooting. In this lab, you will use Wireshark to capture ICMP data packet IP addresses and Ethernet frame MAC addresses.

Required Resources

  • 1 PC (Windows 7, 8, or 10 with internet access)
  • Additional PCs on a local-area network (LAN) will be used to reply to ping requests.

Instructor Note: This lab assumes that the student is using a PC with internet access and can ping other PCs on the local area network.

Using a packet sniffer such as Wireshark may be considered a breach of the security policy of the school. It is recommended that permission be obtained before running Wireshark for this lab. If using a packet sniffer such as Wireshark is an issue, the instructor may wish to assign the lab as homework or perform a walk-through demonstration.

Part 1: Capture and Analyze Local ICMP Data in Wireshark

In Part 1 of this lab, you will ping another PC on the LAN and capture ICMP requests and replies in Wireshark. You will also look inside the frames captured for specific information. This analysis should help to clarify how packet headers are used to transport data to their destination.

Step 1: Retrieve your PC interface addresses.

For this lab, you will need to retrieve your PC IP address and its network interface card (NIC) physical address, also called the MAC address.

a. Open a command window, type ipconfig /all, and then press Enter.

b. Note the IP address of your PC interface, its description, and its MAC (physical) address.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 32

c. Ask a team member or team members for their PC IP address and provide your PC IP address to them. Do not provide them with your MAC address at this time.

Step 2: Start Wireshark and begin capturing data.

a. On your PC, click the Windows Start button to see Wireshark listed as one of the programs on the pop-up menu. Double-click Wireshark.

b. After Wireshark starts, click the capture interface to be used. Because we are using the wired Ethernet connection on the PC, make sure the Ethernet option is on the top of the list.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 33

You can manage the capture interface by clicking Capture and Options:

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 34

c. A list of interfaces will display. Make sure the capture interface is checked under Promiscuous.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 35

Note: We can further manage the interfaces on the PC by clicking Manage Interfaces. Verify that the description matches what you noted in Step 1b. Close the Manage Interfaces window after verifying the correct interface.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 36

d. After you have checked the correct interface, click Start to start the data capture.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 37

Note: You can also start the data capture by clicking the Wireshark icon in the main interface.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 38

Information will start scrolling down the top section in Wireshark. The data lines will appear in different colors based on protocol.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 39

e. This information can scroll by very quickly depending on what communication is taking place between your PC and the LAN. We can apply a filter to make it easier to view and work with the data that is being captured by Wireshark. For this lab, we are only interested in displaying ICMP (ping) PDUs. Type icmp in the Filter box at the top of Wireshark and press Enter or click on the Apply button (arrow sign) to view only ICMP (ping) PDUs.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 40

f. This filter causes all data in the top window to disappear, but you are still capturing the traffic on the interface. Bring up the command prompt window that you opened earlier and ping the IP address that you received from your team member.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 41

Notice that you start seeing data appear in the top window of Wireshark again.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 42

Note: If the PC of your team member does not reply to your pings, this may be because the PC firewall of the team member is blocking these requests. Please see Appendix A: Allowing ICMP Traffic Through a Firewall for information on how to allow ICMP traffic through the firewall using Windows 7.

g. Stop capturing data by clicking the Stop Capture icon.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 43

Step 3: Examine the captured data.

In Step 3, examine the data that was generated by the ping requests of your team member PC. Wireshark data is displayed in three sections: 1) The top section displays the list of PDU frames captured with a summary of the IP packet information listed; 2) the middle section lists PDU information for the frame selected in the top part of the screen and separates a captured PDU frame by its protocol layers; and 3) the bottom section displays the raw data of each layer. The raw data is displayed in both hexadecimal and decimal form.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 44

a. Click the first ICMP request PDU frames in the top section of Wireshark. Notice that the Source column has your PC IP address, and the Destination column contains the IP address of the teammate PC that you pinged.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 45

b. With this PDU frame still selected in the top section, navigate to the middle section. Click the plus sign to the left of the Ethernet II row to view the destination and source MAC addresses.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 46

Does the source MAC address match your PC interface (shown in Step 1.b)? Yes

Does the destination MAC address in Wireshark match your team member MAC address?
Yes
How is the MAC address of the pinged PC obtained by your PC?
The MAC address is obtained through an ARP request.

Note: In the preceding example of a captured ICMP request, ICMP data is encapsulated inside an IPv4 packet PDU (IPv4 header) which is then encapsulated in an Ethernet II frame PDU (Ethernet II header) for transmission on the LAN.

Part 2: Capture and Analyze Remote ICMP Data in Wireshark

In Part 2, you will ping remote hosts (hosts not on the LAN) and examine the generated data from those pings. You will then determine what is different about this data from the data examined in Part 1.

Step 1: Start capturing data on the interface.

a. Start the data capture again.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 47

b. A window prompts you to save the previously captured data before starting another capture. It is not necessary to save this data. Click Continue without Saving.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 48

c. With the capture active, ping the following three website URLs:

1) www.yahoo.com
2) www.cisco.com
3) www.google.com

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 49

Note: When you ping the URLs listed, notice that the Domain Name Server (DNS) translates the URL to an IP address. Note the IP address received for each URL.

d. You can stop capturing data by clicking the Stop Capture icon.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 50

Step 2: Examining and analyzing the data from the remote hosts.

a. Review the captured data in Wireshark and examine the IP and MAC addresses of the three locations that you pinged. List the destination IP and MAC addresses for all three locations in the space provided.

1st Location:
IP: _____._____._____._____ MAC: ____:____:____:____:____:____
2nd Location:
IP: _____._____._____._____ MAC: ____:____:____:____:____:____
3rd Location:
IP: _____._____._____._____ MAC: ____:____:____:____:____:____

_IP addresses: 98.139.180.180, 23.13.155.188, 216.58.194.100 (these IP addresses may vary)
MAC address: This will be the same for all three locations. It is the physical address of the default-gateway LAN interface of the router.

b. What is significant about this information?
The MAC addresses for all three locations are the same.

c. How does this information differ from the local ping information you received in Part 1?
A ping to a local host returns the MAC address of the PC NIC. A ping to a remote host returns the MAC address of the default gateway LAN interface.

Reflection

Why does Wireshark show the actual MAC address of the local hosts, but not the actual MAC address for the remote hosts?
MAC addresses for remote hosts are not known on the local network, so the MAC address of the default-gateway is used. After the packet reaches the default-gateway router, the Layer 2 information is stripped from the packet and a new Layer 2 header is attached with the destination MAC address of the next hop router.

Appendix A: Allowing ICMP Traffic Through a Firewall

If the members of your team are unable to ping your PC, the firewall may be blocking those requests. This appendix describes how to create a rule in the firewall to allow ping requests. It also describes how to disable the new ICMP rule after you have completed the lab.

Step 1: Create a new inbound rule allowing ICMP traffic through the firewall.

a. From the Control Panel, click the System and Security option.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 51

b. From the System and Security window, click Windows Firewall.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 52

c. In the left pane of the Windows Firewall window, click Advanced settings.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 53

d. On the Advanced Security window, choose the Inbound Rules option on the left sidebar and then click New Rule… on the right sidebar.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 54

e. This launches the New Inbound Rule wizard. On the Rule Type screen, click the Custom radio button and click Next.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 55

f. In the left pane, click the Protocol and Ports option and using the Protocol Type drop-down menu, select ICMPv4, and then click Next.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 56

g. In the left pane, click the Name option and in the Name field, type Allow ICMP Requests. Click Finish.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 57

This new rule should allow your team members to receive ping replies from your PC.

Step 2: Disabling or deleting the new ICMP rule.

After the lab is complete, you may want to disable or even delete the new rule you created in Step 1. Using the Disable Rule option allows you to enable the rule again at a later date. Deleting the rule permanently deletes it from the list of inbound rules.

a. On the Advanced Security window, click Inbound Rules in the left pane and then locate the rule you created in Step 1.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 58

b. To disable the rule, click the Disable Rule option. When you choose this option, you will see this option change to Enable Rule. You can toggle back and forth between Disable Rule and Enable Rule; the status of the rule also shows in the Enabled column of the Inbound Rules list.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 59

c. To permanently delete the ICMP rule, click Delete. If you choose this option, you must re-create the rule again to allow ICMP replies.

3.4.1.2 Lab - Using Wireshark to View Network Traffic Answers 60

 

Subscribe
Notify of
guest

0 Comments
Inline Feedbacks
View all comments
0
Would love your thoughts, please comment.x
()
x