8.1.4.7/9.1.4.6 Packet Tracer – Subnetting Scenario 1 Instructions Answers

8.1.4.7/9.1.4.6 Packet Tracer – Subnetting Scenario 1 Instructions Answers
3.9 (11) vote[s]

4

Packet Tracer – Subnetting Scenario 1

Addressing Table

Objectives

Part 1: Design an IP Addressing Scheme

Part 2: Assign IP Addresses to Network Devices and Verify Connectivity

Scenario

In this activity, you are given the network address of 192.168.100.0/24 to subnet and provide the IP addressing for the network shown in the topology. Each LAN in the network requires enough space for, at least, 25 addresses for end devices, the switch and the router. The connection between R1 to R2 will require an IP address for each end of the link.

Part 1: Design an IP Addressing Scheme

Step 1: Subnet the 192.168.100.0/24 network into the appropriate number of subnets.

a. Based on the topology, how many subnets are needed?

b. How many bits must be borrowed to support the number of subnets in the topology table? 3 bits

c. How many subnets does this create? 2^3 = 8 subnets (support subnet zero)

d. How many usable hosts does this create per subnet? 2^5 – 2 = 30 hosts

Note: If your answer is less than the 25 hosts required, then you borrowed too many bits.

e. Calculate the binary value for the first five subnets. The first subnet is already shown.

Net 0: 192 . 168 . 100 . 0 0 0 0 0 0 0 0

Net 1: 192 . 168 . 100 . ___ ___ ___ ___ ___ ___ ___ ___ => 192.168.100.00100000

Net 2: 192 . 168 . 100 . ___ ___ ___ ___ ___ ___ ___ ___ => 192.168.100.01000000

Net 3: 192 . 168 . 100 . ___ ___ ___ ___ ___ ___ ___ ___ => 192.168.100.01100000

Net 4: 192 . 168 . 100 . ___ ___ ___ ___ ___ ___ ___ ___ => 192.168.100.10000000

f. Calculate the binary and decimal value of the new subnet mask.

11111111.11111111.11111111. ___ ___ ___ ___ ___ ___ ___ ___ => 11111111.11111111.11111111.11100000
255 . 255 . 255 . ______ => 255 . 255 . 255 .224

g. Fill in the Subnet Table, listing the decimal value of all available subnets, the first and last usable host address, and the broadcast address. Repeat until all addresses are listed.

Note: You may not need to use all rows.

Subnet Table

Step 2: Assign the subnets to the network shown in the topology.

a. Assign Subnet 0 to the LAN connected to the GigabitEthernet 0/0 interface of R1: – 192.168.100.0 /27

b. Assign Subnet 1 to the LAN connected to the GigabitEthernet 0/1 interface of R1: – 192.168.100.32 /27

c. Assign Subnet 2 to the LAN connected to the GigabitEthernet 0/0 interface of R2: – 192.168.100.64 /27

d. Assign Subnet 3 to the LAN connected to the GigabitEthernet 0/1 interface of R2: – 192.168.100.96 /27

e. Assign Subnet 4 to the WAN link between R1 to R2: – 192.168.100.128 /27

Step 3: Document the addressing scheme.

Fill in the Addressing Table using the following guidelines:

a. Assign the first usable IP addresses to R1 for the two LAN links and the WAN link.

b. Assign the first usable IP addresses to R2 for the LANs links. Assign the last usable IP address for the WAN link.

c. Assign the second usable IP addresses to the switches.

d. Assign the last usable IP addresses to the hosts.

Part 2: Assign IP Addresses to Network Devices and Verify Connectivity

Most of the IP addressing is already configured on this network. Implement the following steps to complete the addressing configuration.

Step 1: Configure IP addressing on R1 LAN interfaces.
Step 2: Configure IP addressing on S3, including the default gateway.
Step 3: Configure IP addressing on PC4, including the default gateway.

Instructions

R1(config)#interface gigabitEthernet 0/0
R1(config-if)#ip address 192.168.100.1 255.255.255.224
R1(config-if)#no shutdown
R1(config-if)#exit

R1(config)#interface gigabitEthernet 0/1
R1(config-if)#ip address 192.168.100.33 255.255.255.224
R1(config-if)#no shutdown

S3>enable
S3#configure terminal
S3(config)#interface vlan 1
S3(config-if)#ip address 192.168.100.66 255.255.255.224
S3(config-if)#no shutdown
S3(config-if)#exit
S3(config)#ip default-gateway 192.168.100.65


2016-10-24_230349
Step 4: Verify connectivity.

You can only verify connectivity from R1, S3, and PC4. However, you should be able to ping every IP address listed in the Addressing Table.

Suggested Scoring Rubric

4

Download Pka file and PDF file below:


Related Articles

Leave a Reply

avatar
Photo and Image Files
 
 
 
Audio and Video Files
 
 
 
Other File Types
 
 
 

Send this to a friend