Lab 6.7.5 – Subnet and Router Configuration (Answers)

Lab 6.7.5 – Subnet and Router Configuration (Answers)

Topology Diagram

Lab 6.7.5 - Subnet and Router Configuration (Answers) 2

Addressing Table

Device Interface IP Address Subnet Mask Default Gateway
R1 Fa0/0 192.168.1.33 255.255.255.224 N/A
S0/0/0 192.168.1.65 255.255.255.224 N/A
R2 Fa0/0 192.168.1.97 255.255.255.224 N/A
S0/0/0 192.168.1.94 255.255.255.224 N/A
PC1 NIC 192.168.1.62 255.255.255.224 192.168.1.33
PC2 NIC 192.168.1.126 255.255.255.224 192.168.1.97

Learning Objectives

Upon completion of this lab, you will be able to:

  • Subnet an address space per given requirements.
  • Assign appropriate addresses to interfaces and document.
  • Configure and activate Serial and FastEthernet interfaces.
  • Test and verify configurations.
  • Reflect upon and document the network implementation.

Scenario

In this lab activity, you will design and apply an IP addressing scheme for the topology shown in the Topology Diagram. You will be given one address block that you must subnet to provide a logical addressing scheme for the network. The routers will then be ready for interface address configuration according to your IP addressing scheme. When the configuration is complete, verify that the network is working properly.

Task 1: Subnet the Address Space.

Step 1: Examine the network requirements.

You have been given the 192.168.1.0/24 address space to use in your network design. The network consists of the following segments:

  • The LAN connected to router R1 will require enough IP addresses to support 15 hosts.
  • The LAN connected to router R2 will require enough IP addresses to support 30 hosts.
  • The link between router R1 and router R2 will require IP addresses at each end of the link.

The plan should have equal size subnets and use the smallest subnet sizes that will accommodate the appropriate number of hosts.

Step 2: Consider the following questions when creating your network design.

How many subnets are needed for this network?
3

What is the subnet mask for this network in dotted decimal format?
255.255.255.224

What is the subnet mask for the network in slash format?
/27

How many usable hosts are there per subnet?
30

Step 3: Assign subnetwork addresses to the Topology Diagram.

1. Assign second subnet to the network attached to R1.

2. Assign third subnet to the link between R1 and R2.

3. Assign fourth subnet to the network attached to R2.

Instructor Note: To be consistent with current networking practices, subnet 0 is always usable and is considered the first subnet. In this example, we are starting with the “second” subnet which is the .32 subnet.

Task 2: Determine Interface Addresses.

Step 1: Assign appropriate addresses to the device interfaces.

1. Assign the first valid host address in second subnet to the LAN interface on R1.

2. Assign the last valid host address in second subnet to PC1.

3. Assign the first valid host address in third subnet to the WAN interface on R1.

4. Assign the last valid host address in third subnet to the WAN interface on R2.

5. Assign the first valid host address in fourth subnet to the LAN interface of R2.

6. Assign the last valid host address in fourth subnet to PC2.

Step 2: Document the addresses to be used in the table provided under the Topology Diagram.

Task 3: Configure the Serial and FastEthernet Addresses.

Step 1: Configure the router interfaces.

Configure the interfaces on the R1 and R2 routers with the IP addresses from your network design. Please note, to complete the activity in Packet Tracer you will be using the Config Tab. When you have finished, be sure to save the running configuration to the NVRAM of the router.

Step 2: Configure the PC interfaces.

Configure the Ethernet interfaces of PC1 and PC2 with the IP addresses and default gateways from your network design.

Task 4: Verify the Configurations.

Answer the following questions to verify that the network is operating as expected.

From the host attached to R1, is it possible to ping the default gateway?
Yes

From the host attached to R2, is it possible to ping the default gateway?
Yes

From the router R1, is it possible to ping the Serial 0/0/0 interface of R2?
Yes

From the router R2, is it possible to ping the Serial 0/0/0 interface of R1?
Yes

The answer to the above questions should be yes. If any of the above pings failed, check your physical connections and configurations.

Task 5: Reflection

Are there any devices on the network that cannot ping each other?
________________________________________________

What is missing from the network that is preventing communication between these devices?
________________________________________________

 

Subscribe
Notify of
guest

0 Comments
Inline Feedbacks
View all comments