IT Questions Bank

IT Questions Bank 1

A company is expanding business by opening 35 branches over the Internet. A network engineer must configure DMVPN at the branch routers to connect with the hub router and allow NHRP to add spoke routers securely to the multicast NHRP mappings automatically Which configuration meets this requirement at the hub router?
IT Questions Bank 2IT Administrator asked 3 years ago • 
What is a function of IPv6 Source Guard?
IT Questions Bank 2IT Administrator asked 3 years ago • 
Refer to the exhibit. An engineer must block access to the console ports for all corporate remote Cisco devices based on the recent corporate security policy but the security team stilt can connect through the console port. Which configuration on the console port resolves the issue?
IT Questions Bank 2IT Administrator asked 3 years ago • 
Refer to the exhibit. A junior engineer configured SNMP to network devices. Malicious users have uploaded different configurations to the network devices using SNMP and TFTP servers. Which configuration prevents changes from unauthorized NMS and TFTP servers?
IT Questions Bank 2IT Administrator asked 3 years ago • 
Refer to the exhibit. An engineer has configured R1 as EIGRP stub router. After the configuration, router R3 failed to reach to R2 loopback address. Which action advertises R2 loopback back into the R3 routing table?
IT Questions Bank 2IT Administrator asked 3 years ago • 
Refer to the exhibit. The network administrator configured the network to connect two disjointed networks and ail the connectivity is up except the virtual link which causes area 250 to be unreachable. Which two configurations resolve this issue? (Choose two.)
IT Questions Bank 2IT Administrator asked 3 years ago • 
Refer to the exhibit. The DHCP client is unable to receive an IP address from the DHCP server RouterB is configured as follows: Which command is required on the fastethernet 0/0 interface of RouterB to resolve this issue?
IT Questions Bank 2IT Administrator asked 3 years ago • 
Refer to the exhibit. The branch router is configured with a default route toward the internet and has no routes configured for the HQ site that is connected through interface G2/0. The HQ router is fully configured and does not require changes. Which configuration on the branch router makes the intranet website (TCP port 80) available to the branch office users?
IT Questions Bank 2IT Administrator asked 3 years ago • 
Refer to the exhibit. The Internet traffic should always prefer Site-A ISP-1 if the link and BGP connection are up; otherwise, all Internet traffic should go to ISP-2 Redistribution is configured between BGP and OSPF routing protocols and it is not working as expected. What action resolves the issue?
IT Questions Bank 2IT Administrator asked 3 years ago • 
Refer to the exhibit. The administrator configured the network devise for end-to-end reachability, but the ASBRs are not propagation routes to each other. Which set of configuration resolves this issue?
IT Questions Bank 2IT Administrator asked 3 years ago • 
Refer to the exhibit. R1 is configured with uRPF, and ping to R1 is failing from a source present in the R1 routing table via the GigatxtEthernet 0/0 interface. Which action resolves the issue?
IT Questions Bank 2IT Administrator asked 3 years ago • 
The network administrator configured CoPP so that all HTTP and HTTPS traffic from the administrator device located at 172.16 1.99 toward the router CPU is limited to 500 kbps. Any traffic that exceeds this limit must be dropped. CoPP failed to capture the desired traffic and the CPU load is getting higher. Which two configurations resolve the issue? (Choose two.)
IT Questions Bank 2IT Administrator asked 3 years ago • 
An engineer creates a Cisco DNA Center cluster with three nodes, but all the services are running on one host node. Which action resolves this issue?
IT Questions Bank 2IT Administrator asked 3 years ago • 
Refer to the exhibit. A network administrator is troubleshooting IPv6 address assignment for a DHCP client that is not getting an IPv6 address from the server. Which configuration retrieves the client IPv6 address from the DHCP server?
IT Questions Bank 2IT Administrator asked 3 years ago • 
Refer to the exhibit. While monitoring VTY access to a router, an engineer notices that the router does not have any filter and anyone can access the router with username and password even though an ACL is configured. Which command resolves this issue?
IT Questions Bank 2IT Administrator asked 3 years ago • 
« Previous1…824825826827828…1,321Next »
Ask Question