9.4.1.2 Packet Tracer – Skills Integration Challenge Instructions Answers.

9.4.1.2 Packet Tracer – Skills Integration Challenge (Instructor Version)

Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only.

Topology

9.4.1.2 Packet Tracer - Skills Integration Challenge Instructions Answers. 2

Addressing Table

Instructor Note: The student version has blanks in place of all variables shown in double brackets.

Device Interface IP Address Subnet Mask Default Gateway
[[R1Name]] G0/0.15 [[R1G0sub15Add]] [[R1G0sub15SM]] N/A
G0/0.30 [[R1G0sub30Add]] [[R1G0sub30SM]] N/A
G0/0.45 [[R1G0sub45Add]] [[R1G0sub45SM]] N/A
G0/0.60 [[R1G0sub60Add]] [[R1G0sub60SM]] N/A
S0/0/0 [[R1S000Add]] 255.255.255.252 N/A
S0/0/1 [[R1S001Add]] 255.255.255.252 N/A
S0/1/0 [[R1S010Add]] 255.255.255.252 N/A
[[R2Name]] G0/0 [[R2G00Add]] [[R2R3LanSM]] N/A
S0/0/0 [[R2S000Add]] 255.255.255.252 N/A
S0/0/1 [[R2S001Add]] 255.255.255.252 N/A
[[R3Name]] G0/0 [[R3G00Add]] [[R2R3LanSM]] N/A
S0/0/0 [[R3S000Add]] 255.255.255.252 N/A
S0/0/1 [[R3S001Add]] 255.255.255.252 N/A
[[S1Name]] VLAN 60 [[S1VLAN60Add]] [[R1G0sub60SM]] [[R1G0sub60Add]]
[[PC1Name]] NIC DHCP Assigned DHCP Assigned DHCP Assigned

VLANs and Port Assignments Table

VLAN Number – Name Port assignment Network
15 – Servers F0/11 – F0/20 [[R1-VLANsrvNet]]
30 – PCs F0/1 – F0/10 [[R1-VLANpcNet]]
45 – Native G0/1 [[R1-VLANntvNet]]
60 – Management VLAN 60 [[R1-VLANmanNet]]

Scenario

This culminating activity includes many of the skills that you have acquired during this course. First, you will complete the documentation for the network. Make sure you have a printed version of the instructions. During implementation, you will configure VLANs, trunking, port security and SSH remote access on a switch. You will then implement inter-VLAN routing and NAT on a router. Finally, you will use your documentation to verify your implementation by testing end-to-end connectivity.

Documentation

You are required to fully document the network. You will need a print out of this instruction set, which will include an unlabeled topology diagram:

  • Label all the device names, network addresses and other important information that Packet Tracer generated.
  • Complete the Addressing Table and VLANs and Port Assignments Table.
  • Fill in any blanks in the Implementation and Verification The information is supplied when you launch the Packet Tracer activity.

Implementation

Note: All devices in the topology except [[R1Name]], [[S1Name]], and [[PC1Name]] are fully configured. You do not have access to the other routers. You can access all the servers and PCs for testing purposes.

Implement to following requirements using your documentation:

[[S1Name]]

  • Configure remote management access including IP addressing and SSH:
    • Domain is cisco.com
    • User [[UserText]] with password [[UserPass]]
    • Crypto key length of 1024
    • SSH version 2, limited to 2 authentication attempts and a 60 second timeout using the following commands:
      ip ssh version 2
      ip ssh authentication-retries 2
      ip ssh time-out 60
    • Clear text passwords should be encrypted.
  • Configure, name and assign VLANs. Ports should be manually configured as access ports.
  • Configure trunking.
  • Implement port security:
    • On Fa0/1, allow 2 MAC addresses that are automatically added to the configuration file when detected. The port should not be disabled, but a syslog message should be captured if a violation occurs.
    • Disable all other unused ports.

[[R1Name]]

  • Configure inter-VLAN routing.
  • Configure DHCP services for VLAN 30. Use LAN as the case-sensitive name for the pool.
  • Implement routing:
    • Use RIPv2 as the routing protocol.
    • Configure one network statement for the entire [[DisplayNet]] address space.
    • Disable interfaces that should not send RIPv2 messages.
    • Configure a default route to the Internet.
  • Implement NAT:
    • Configure a standard, one statement ACL number 1. All IP addresses belonging to the [[DisplayNet]] address space are allowed.
    • Refer to your documentation and configure static NAT for the File Server.
    • Configure dynamic NAT with PAT using a pool name of your choice, a /30 mask, and these two public addresses:
      • [[NATPoolText]]
      • [[PC1Name]]

Verify [[PC1Name]] has received full addressing information from [[R1Name]].

Verification

All devices should now be able to ping all other devices. If not, troubleshoot your configurations to isolate and solve problems. A few tests include:

  • Verify remote access to [[S1Name]] by using SSH from a PC.
  • Verify VLANs are assigned to appropriate ports and port security is in force.
  • Verify OSPF neighbors and a complete routing table.
  • Verify NAT translations and statics.
    • Outside Host should be able to access File Server at the public address.
    • Inside PCs should be able to access Web Server.
  • Document any problems you encountered and the solutions in the Troubleshooting Documentation table below.

Troubleshooting Documentation

Problem Solution

Suggested Scoring Rubric

Packet Tracer scores 70 points. Documentation is worth 30 points.

ID:[[indexAdds]][[indexNames]]

*****************************************************
ISOMORPH ID KEY:
ID = XY where;
 X = indexAdds for /24 private address space
 Y = indexNAMES for device names
Note: Each seed contains variables that are independent 
of the other seeds. You do not need to test all the 
various combinations.
=======================================================
ISOMORPH ID = 00
=======================================================
!HQ!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
en
conf t
ip dhcp pool LAN
 network 172.16.15.32 255.255.255.224
 default-router 172.16.15.33
interface GigabitEthernet0/0
 no shutdown
interface GigabitEthernet0/0.15
 encapsulation dot1Q 15
 ip address 172.16.15.17 255.255.255.240
 ip nat inside
interface GigabitEthernet0/0.30
 encapsulation dot1Q 30
 ip address 172.16.15.33 255.255.255.224
 ip nat inside
interface GigabitEthernet0/0.45
 encapsulation dot1Q 45 native
 ip address 172.16.15.1 255.255.255.248
interface GigabitEthernet0/0.60
 encapsulation dot1Q 60
 ip address 172.16.15.9 255.255.255.248
router rip
 version 2
 passive-interface GigabitEthernet0/0
 passive-interface Serial0/1/0
 network 172.16.0.0
!
ip nat pool TEST 209.165.200.225 209.165.200.226 netmask 255.255.255.252
ip nat inside source list 1 pool TEST overload
ip nat inside source static 172.16.15.18 209.165.200.227 
ip route 0.0.0.0 0.0.0.0 Serial0/1/0 
access-list 1 permit 172.16.15.0 0.0.0.255
interface s0/0/0
 ip nat inside
interface s0/0/1
 ip nat inside
interface s0/1/0
 ip nat outside
end
wr
!!!!!!!!!!!!!!!!!!!!!!!!
!HQ-Sw!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!
en
conf t
int vlan 60
ip add 172.16.15.10 255.255.255.248
no shut
ip default-gateway 172.16.15.9
vlan 15
name Servers
vlan 30
name PCs
vlan 45
name Native
vlan 60
name Management
interface range fa0/1 - 10
switchport mode access
switchport access vlan 30
interface fa0/1
switchport port-security
switchport port-security maximum 2
switchport port-security mac-address sticky 
switchport port-security violation restrict 
interface range fa0/11 - 20
switchport mode access
switchport access vlan 15
interface g0/1
switchport mode trunk
switchport trunk native vlan 45
interface range fa0/21 - 24 , g0/2
shutdown
ip domain-name cisco.com
crypto key gen rsa
1024

user HQadmin pass ciscoclass
service password-encryption
ip ssh version 2
ip ssh auth 2
ip ssh time 60
line vty 0 15
login local
transport input ssh

=======================================================
ISOMORPH ID = 11
=======================================================
!Admin!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
en
conf t
ip dhcp pool LAN
 network 10.10.10.192 255.255.255.192
 default-router 10.10.10.193
interface GigabitEthernet0/0
 no shutdown
interface GigabitEthernet0/0.15
 encapsulation dot1Q 15
 ip address 10.10.10.161 255.255.255.224
 ip nat inside
interface GigabitEthernet0/0.30
 encapsulation dot1Q 30
 ip address 10.10.10.193 255.255.255.192
 ip nat inside
interface GigabitEthernet0/0.45
 encapsulation dot1Q 45 native
 ip address 10.10.10.129 255.255.255.240
interface GigabitEthernet0/0.60
 encapsulation dot1Q 60
 ip address 10.10.10.145 255.255.255.240
router rip
 version 2
 passive-interface GigabitEthernet0/0
 network 172.16.0.0
interface s0/0/0
 ip nat inside
interface s0/0/1
 ip nat inside
interface s0/1/0
 ip nat outside
!
ip nat pool TEST 198.133.219.128 198.133.219.129 netmask 255.255.255.252
ip nat inside source list 1 pool TEST overload
ip nat inside source static 10.10.10.162 198.133.219.130
ip route 0.0.0.0 0.0.0.0 Serial0/1/0 
access-list 1 permit 10.10.10.0 0.0.0.255
end
wr
!!!!!!!!!!!!!!!!!!!!!!!!
!Admin-Sw!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
en
conf t
int vlan 60
ip add 10.10.10.146 255.255.255.240
no shut
ip default-gateway 10.10.10.145
vlan 15
name Servers
vlan 30
name PCs
vlan 45
name Native
vlan 60
name Management
interface range fa0/1 - 10
switchport mode access
switchport access vlan 30
interface fa0/1
switchport port-security
switchport port-security maximum 2
switchport port-security mac-address sticky 
switchport port-security violation restrict 
interface range fa0/11 - 20
switchport mode access
switchport access vlan 15
interface g0/1
switchport mode trunk
switchport trunk native vlan 45
interface range fa0/21 - 24 , g0/2
shutdown
ip domain-name cisco.com
crypto key gen rsa
1024

user Admin pass letmein
service password-encryption
ip ssh version 2
ip ssh auth 2
ip ssh time 60
line vty 0 15
login local
transport input ssh

===============================================================
ISOMORPH ID: 22
===============================================================
!Central!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
en
conf t
ip dhcp pool LAN
 network 192.168.45.128 255.255.255.192
 default-router 192.168.45.129
interface GigabitEthernet0/0
 no shutdown
interface GigabitEthernet0/0.15
 encapsulation dot1Q 15
 ip address 192.168.45.65 255.255.255.192
 ip nat inside
interface GigabitEthernet0/0.30
 encapsulation dot1Q 30
 ip address 192.168.45.129 255.255.255.192
 ip nat inside
interface GigabitEthernet0/0.45
 encapsulation dot1Q 45 native
 ip address 192.168.45.17 255.255.255.240
interface GigabitEthernet0/0.60
 encapsulation dot1Q 60
 ip address 192.168.45.33 255.255.255.240
router rip
 version 2
 passive-interface GigabitEthernet0/0
 network 172.16.0.0
interface s0/0/0
 ip nat inside
interface s0/0/1
 ip nat inside
interface s0/1/0
 ip nat outside
!
ip nat pool TEST 64.100.32.56 64.100.32.57 netmask 255.255.255.252
ip nat inside source list 1 pool TEST overload
ip nat inside source static 192.168.45.66 64.100.32.58
ip route 0.0.0.0 0.0.0.0 Serial0/1/0 
access-list 1 permit 192.168.45.0 0.0.0.255
end
wr
!!!!!!!!!!!!!!!!!!!!!!!!
!Cnt-Sw!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
en
conf t
int vlan 60
ip add 192.168.45.34 255.255.255.240
no shut
ip default-gateway 192.168.45.33
vlan 15
name Servers
vlan 30
name PCs
vlan 45
name Native
vlan 60
name Management
interface range fa0/1 - 10
switchport mode access
switchport access vlan 30
interface fa0/1
switchport port-security
switchport port-security maximum 2
switchport port-security mac-address sticky 
switchport port-security violation restrict 
interface range fa0/11 - 20
switchport mode access
switchport access vlan 15
interface g0/1
switchport mode trunk
switchport trunk native vlan 45
interface range fa0/21 - 24 , g0/2
shutdown
ip domain-name cisco.com
crypto key gen rsa
1024

user CAdmin pass itsasecret
service password-encryption
ip ssh version 2
ip ssh auth 2
ip ssh time 60
line vty 0 15
login local
transport input ssh

Download Packet Tracer (.pka) file:

Subscribe
Notify of
guest

0 Comments
Inline Feedbacks
View all comments