Lab 11.5.3 – Configure Host Computers for IP Networking (Answers)

Lab 11.5.3 – Configure Host Computers for IP Networking (Answers)

Topology Diagram

Learning Objectives

Upon completion of this lab, you will be able to:

• Design the logical lab topology.
• Configure the physical lab topology.
• Configure the logical LAN topology.
• Verify LAN connectivity.

Background

Table 1. Equipment and Hardware for this Lab

Gather the necessary equipment and cables. To configure the lab, make sure the equipment listed in Table 1 is available.

Scenario

In this lab students will create a small network that requires connecting network devices and configuring host computers for basic network connectivity. The Appendix is a reference for configuring the logical network.

Note to instructor: To reinforce student cable identification, have several different types of cables available for the students. Mix cross-over, straight-through, and rollover cables. Students should be able to identify the proper cable type based on a visual inspection.

Task 1: Design the Logical Lab Topology.

1. Given an IP address of 192.168.254.0/24, and 5 bits used for subnets, fill in the following information:

Maximum number of subnets: 32

Number of usable Hosts per subnet: 6

2. Before proceeding, verify your addresses with the instructor. The instructor will assign one subnetwork per student or team.

Task 2: Configure the Physical Lab Topology.

Step 1: Physically connect devices.

1. Cable the network devices as shown in Figure 1.

Figure 1. Cabling the Network

Is a crossover cable needed to connect Host computers to the switch? Why or why not?
Answer: No. Since computers and the switch are not wired the same for networking, straightthrough cables are used.

If not already enabled, turn power on to all devices.

Step 2: Visually inspect network connections.

After cabling the network devices, take a moment to verify the connections. Attention to detail now will minimize the time required to troubleshoot network connectivity issues later.

Task 3: Configure the Logical Topology.

Step 1: Document logical network settings.

1. Host computers will use the first two IP addresses in the subnetwork. Write down the IP address information for each device:

Figure 2. Logical Topology

2. From the information given in Figure 2, write down the IP network addressing for each computer:

Step 2: Configure Host1 computer.

1. On Computer1, click Start > Control Panel > Network Connections. Right-click the LAN icon, and choose Properties. On the General tab, select Internet Protocol (TCP/IP), and then click the Properties button.

Figure 3. Host1 IP Address and Gateway Settings

2. Refer to Figure 3 for Host1 IP address and gateway settings.

3. When finished, click OK, then click Close. The computer may require a reboot for changes to be effective.

4. Verify proper configuration of Host1 with the ipconfig /all command.

5. Record the output below:

Step 3: Configure Host2.

1. Repeat Step 2 for Host2, using IP address information from the table filled out in Step 1.

2. Verify proper configuration of Host1 with the ipconfig /all command.

3. Record the output below:

Task 4: Verify Network Connectivity.

Network connectivity can be verified with the Windows ping command.

1. Use the following table to methodically verify connectivity with each network device:

2. Take corrective action to establish connectivity if a test fails.

Note: If pings to host computers fail, temporarily disable the computer firewall and retest. To disable a Windows firewall, click Start > Control Panel > Windows Firewall, choose Off, and then click OK.

Task 5: Reflection

Review any physical or logical configuration problems encountered during this lab. Make sure you have a thorough understanding of the procedures used to configure a Windows host computer.

Task 6: Challenge

Ask your instructor or another student to introduce one or two problems in your network when you aren’t looking or are out of the lab room. Problems can be either physical (wrong UTP cable) or logical (wrong IP address). To fix the problems:

1. Perform a good visual inspection. Look for green link lights on Switch1.

2. Use the table provided in Task 3, above, to identify failed connectivity. List the problems:

3. Write down your proposed solution(s):

4. Test your solution. If the solution fixed the problem, document the solution. If the solution did not fix the problem, continue troubleshooting.

Task 7: Clean Up.

Unless directed otherwise by the instructor, restore host computer network connectivity, and then turn off power to the host computers. Remove anything that was brought into the lab, and leave the room ready for the next class.

Appendix