7.2.1.6 Packet Tracer – Configuring Numbered Standard IPv4 ACLs Instructions Answers

7.2.1.6 Packet Tracer – Configuring Numbered Standard IPv4 ACLs Instructions Answers
3.6 (7) vote[s]

Packet Tracer – Configuring Numbered Standard IPv4 ACLs

Addressing Table

Objectives

Part 1: Plan an ACL Implementation
Part 2: Configure, Apply, and Verify a Standard ACL

Background / Scenario

Standard access control lists (ACLs) are router configuration scripts that control whether a router permits or denies packets based on the source address. This activity focuses on defining filtering criteria, configuring standard ACLs, applying ACLs to router interfaces, and verifying and testing the ACL implementation. The routers are already configured, including IP addresses and Enhanced Interior Gateway Routing Protocol (EIGRP) routing.

Part 1: Plan an ACL Implementation

Step 1: Investigate the current network configuration.

Before applying any ACLs to a network, it is important to confirm that you have full connectivity. Verify that the network has full connectivity by choosing a PC and pinging other devices on the network. You should be able to successfully ping every device.

Step 2: Evaluate two network policies and plan ACL implementations.

a. The following network policies are implemented on R2:

  • The 192.168.11.0/24 network is not allowed access to the WebServer on the 192.168.20.0/24 network.
  • All other access is permitted.

To restrict access from the 192.168.11.0/24 network to the WebServer at 192.168.20.254 without interfering with other traffic, an ACL must be created on R2. The access list must be placed on the outbound interface to the WebServer. A second rule must be created on R2 to permit all other traffic.

b.  The following network policies are implemented on R3:

  • The 192.168.10.0/24 network is not allowed to communicate with the 192.168.30.0/24 network.
  • All other access is permitted.

To restrict access from the 192.168.10.0/24 network to the 192.168.30/24 network without interfering with other traffic, an access list will need to be created on R3. The ACL must be placed on the outbound interface to PC3. A second rule must be created on R3 to permit all other traffic.

Part 2: Configure, Apply, and Verify a Standard ACL

Step 1: Configure and apply a numbered standard ACL on R2.

a. Create an ACL using the number 1 on R2 with a statement that denies access to the 192.168.20.0/24 network from     the 192.168.11.0/24 network.

R2(config)# access-list 1 deny 192.168.11.0 0.0.0.255

b. By default, an access list denies all traffic that does not match any rules. To permit all other traffic, configure the following statement:

R2(config)# access-list 1 permit any

c. For the ACL to actually filter traffic, it must be applied to some router operation. Apply the ACL by placing it for outbound traffic on the Gigabit Ethernet 0/0 interface.

R2(config)# interface GigabitEthernet0/0

R2(config-if)# ip access-group 1 out
Step 2: Configure and apply a numbered standard ACL on R3.

a. Create an ACL using the number 1 on R3 with a statement that denies access to the 192.168.30.0/24 network from     the PC1 (192.168.10.0/24) network.

R3(config)# access-list 1 deny 192.168.10.0 0.0.0.255

b. By default, an ACL denies all traffic that does not match any rules. To permit all other traffic, create a second rule        for ACL 1.

R3(config)# access-list 1 permit any

c. Apply the ACL by placing it for outbound traffic on the Gigabit Ethernet 0/0 interface.

R3(config)# interface GigabitEthernet0/0

R3(config-if)# ip access-group 1 out
Step 3: Verify ACL configuration and functionality.

a. On R2 and R3, enter the show access-list command to verify the ACL configurations. Enter the show run or         show ip interface gigabitethernet 0/0 command to verify the ACL placements.

b. With the two ACLs in place, network traffic is restricted according to the policies detailed in Part 1. Use the                   following tests to verify the ACL implementations:

  • A ping from 192.168.10.10 to 192.168.11.10 succeeds.
  • A ping from 192.168.10.10 to 192.168.20.254 succeeds.
  • A ping from 192.168.11.10 to 192.168.20.254 fails.
  • A ping from 192.168.10.10 to 192.168.30.10 fails.
  • A ping from 192.168.11.10 to 192.168.30.10 succeeds.
  • A ping from 192.168.30.10 to 192.168.20.254 succeeds.

Related Articles

Leave a Reply

avatar
Photo and Image Files
 
 
 
Audio and Video Files
 
 
 
Other File Types
 
 
 

Send this to a friend